 twin throttle linkage..., Why can't I get this to work????? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| crash914 |
 Mar 22 2005, 07:11 PM
Post
#21
|
|
its a mystery to me  Group: Members Posts: 1,826 Joined: 17-March 03 From: Marriottsville, MD Member No.: 434 Region Association: MidAtlantic Region  |
ok, for all you twin carb/throttle body experts out there....
I have a redline weber twin throttle body set up....got the linkage cross bar etc. from the same place... I can't get this stupid thing to work correctly (IMG:http://www.914world.com/bbs2/html/emoticons/ar15.gif) I can get the right side to open and close fully and the other won't open all the way...I have switched everything around many different ways...even changed out the linkage cams...??? The linkages rotate into the center of the motor...flip the carbs around? so they rotate out? the ball for the cross bar is down...if I flip it over, it will interfer with the air cleaner?? THis is driving me crazy!!! the only thing that I can figure out is that the holes are drilled off. one must be out further than the other..or the carbs need to rotate different amounts...??? I also can't figure out how to mount the crossbar to the front of the motor...I guess I could make up another cable stop...but??? I guess I can shoot some pics when I cool down...now for (IMG:http://www.914world.com/bbs2/html/emoticons/beer.gif) thanks! |
   |
 
|
Posts in this topic
crash914 twin throttle linkage... Mar 22 2005, 07:11 PM
MecGen I think you would need to see a pic,
someone here ... Mar 22 2005, 07:24 PM john rogers Couple of things to check. Does each one open full... Mar 22 2005, 07:26 PM crash914 Thanks for the insite....
yes, the throttles open... Mar 23 2005, 06:30 AM Tom Perso Get the CB Performance linkage setup. I think it... Mar 23 2005, 06:56 AM Joe Sharp If you have a center piviot linkage it is a POS. W... Mar 23 2005, 08:13 AM Aaron Cox never had a problem with my CB linkage....
miles ... Mar 23 2005, 08:42 AM rhodyguy i don't know the dial in for the center pull l... Mar 23 2005, 09:26 AM GBallantine I use the CB Performance Hex Bar Linkage setup on ... Mar 23 2005, 09:54 AM rhodyguy staying in the verticle plane absolutely, is hard ... Mar 23 2005, 10:09 AM Aaron Cox kevin,
it took me 5 minutes tops to make a good t... Mar 23 2005, 10:12 AM rhodyguy i just bolted mine on after i opened the box. ... Mar 23 2005, 07:29 PM Aaron Cox not sure if you can see... but the pivot onb this ... Mar 23 2005, 07:30 PM Series9 You've got things backwards and upside-down. ... Mar 23 2005, 07:49 PM Series9 After looking at it some more, I think you can jus... Mar 23 2005, 07:53 PM crash914 I need to get some more pictures...
When I flip o... Mar 24 2005, 06:04 AM Joe Sharp That linkage should work out just like the picture... Mar 24 2005, 08:43 AM Joe Sharp I thought I had that bracket. Sorry about the san... Mar 24 2005, 08:52 AM rhodyguy are the arms movable on the rod? if so, you need t... Mar 24 2005, 09:03 AM Aaron Cox ... Mar 24 2005, 10:05 AM rhodyguy i bet his arms bang on the fliter bases now that i... Mar 24 2005, 10:25 AM Travis Neff I'd add that your droplinks - are they right a... Mar 24 2005, 10:42 AM Aaron Cox not worth fuching with it...
buy a Triad or a CB ... Mar 24 2005, 11:07 AM rhodyguy -1. get the triad. oh, too much money http://www.914... Mar 25 2005, 08:20 AM crash914 http://www.914world.com/bbs2/... Mar 26 2005, 07:21 PM Joe Sharp Kewl http://www.914world.com/... Mar 26 2005, 07:50 PM Joe Sharp Herb: Check out the linkage on Chris Foley's e... Mar 27 2005, 07:47 AM rhodyguy motorvating!! happy easter! your neigh... Mar 27 2005, 09:37 AM crash914 Yea, I just went around the block a few times...I ... Mar 27 2005, 12:33 PM Joe Sharp I say again!! http://... Mar 27 2005, 01:06 PM
crash914 I knew that it was comming......now where did I pu... Mar 28 2005, 06:51 AM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 18th May 2024 - 05:38 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.