Value of vw/porsche engine yoke? |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
Value of vw/porsche engine yoke? |
mb911 |
Nov 18 2017, 08:17 PM
Post
#1
|
914 Guru Group: Members Posts: 6,802 Joined: 2-January 09 From: Burlington wi Member No.: 9,892 Region Association: Upper MidWest |
|
mb911 |
Nov 18 2017, 08:18 PM
Post
#2
|
914 Guru Group: Members Posts: 6,802 Joined: 2-January 09 From: Burlington wi Member No.: 9,892 Region Association: Upper MidWest |
|
Mueller |
Nov 18 2017, 08:55 PM
Post
#3
|
914 Freak! Group: Members Posts: 17,146 Joined: 4-January 03 From: Antioch, CA Member No.: 87 Region Association: None |
Not cheap at Pelican!
http://www.pelicanparts.com/cgi-bin/ksearc...on=engine+stand I need one, but cannot justify anywhere near those prices for something I might only use once. |
mb911 |
Nov 18 2017, 09:22 PM
Post
#4
|
914 Guru Group: Members Posts: 6,802 Joined: 2-January 09 From: Burlington wi Member No.: 9,892 Region Association: Upper MidWest |
Not cheap at Pelican! http://www.pelicanparts.com/cgi-bin/ksearc...on=engine+stand I need one, but cannot justify anywhere near those prices for something I might only use once. Looks like new it could be as much as a 600 dollar combo.. Used has to much less. Mine is probably 30 years old.. I bought it used 20 years ago.. |
Mueller |
Nov 18 2017, 09:37 PM
Post
#5
|
914 Freak! Group: Members Posts: 17,146 Joined: 4-January 03 From: Antioch, CA Member No.: 87 Region Association: None |
I'm guessing the cutout on the tab on the left hand side is for the tool that holds the flywheel from spinning?
|
rgalla9146 |
Nov 18 2017, 09:56 PM
Post
#6
|
Advanced Member Group: Members Posts: 4,545 Joined: 23-November 05 From: Paramus NJ Member No.: 5,176 Region Association: None |
|
Mueller |
Nov 18 2017, 09:59 PM
Post
#7
|
914 Freak! Group: Members Posts: 17,146 Joined: 4-January 03 From: Antioch, CA Member No.: 87 Region Association: None |
I'm guessing the cutout on the tab on the left hand side is for the tool that holds the flywheel from spinning? Yes, and it's reversible to fit Porsche 12 v or VW / Porsche 6 v flywheels....if... you have it ! ^Neat, there is really cheap looking VW yoke and stand on local CL right now for $80, too bad it is 1.5 hour away one way ... don't think I'd trust this cheaper one with a /6 engine for sure (listed as VW Type I and 912) |
r_towle |
Nov 18 2017, 10:35 PM
Post
#8
|
Custom Member Group: Members Posts: 24,560 Joined: 9-January 03 From: Taxachusetts Member No.: 124 Region Association: North East States |
That looks like a vw yoke.
The Porsche yokes I have seen have more than two arms |
burton73 |
Nov 18 2017, 11:26 PM
Post
#9
|
burton73 Group: Members Posts: 3,487 Joined: 2-January 07 From: Los Angeles Member No.: 7,414 Region Association: Southern California |
EBay 5 arm stand for $130 with shipping. Someone could buy a roll stand from a local store for cheep. That is what I did no my last rebuild. The 6 eng did not fall down.
So what is yours worth? If a guy was a pro he would have a good one like yours (IMG:style_emoticons/default/rolleyes.gif) Bob B |
mb911 |
Nov 19 2017, 06:04 AM
Post
#10
|
914 Guru Group: Members Posts: 6,802 Joined: 2-January 09 From: Burlington wi Member No.: 9,892 Region Association: Upper MidWest |
|
infraredcalvin |
Nov 19 2017, 06:14 AM
Post
#11
|
Distracted Member Group: Members Posts: 1,504 Joined: 25-August 08 From: Ladera Ranch, CA Member No.: 9,463 Region Association: Southern California |
For reference, i just bought a 5 arm P201 along with a used harbor freight engine stand for 200 on the bird not too long ago , I think it was a good deal. I didn’t realize the “new”prices had gone up that much, for some reason I remember a new five arm costing around 275-300.
|
mb911 |
Nov 19 2017, 07:00 AM
Post
#12
|
914 Guru Group: Members Posts: 6,802 Joined: 2-January 09 From: Burlington wi Member No.: 9,892 Region Association: Upper MidWest |
For reference, i just bought a 5 arm P201 along with a used harbor freight engine stand for 200 on the bird not too long ago , I think it was a good deal. I didn’t realize the “new”prices had gone up that much, for some reason I remember a new five arm costing around 275-300. Thanks I just came up with a price of 325 in the classifieds and 375 on the bird board. We will see what happens. |
mepstein |
Nov 19 2017, 07:19 AM
Post
#13
|
914-6 GT in waiting Group: Members Posts: 19,234 Joined: 19-September 09 From: Landenberg, PA/Wilmington, DE Member No.: 10,825 Region Association: MidAtlantic Region |
It’s a great deal. Buy it, use it and then sell it for what you paid.
|
bdstone914 |
Nov 19 2017, 07:58 AM
Post
#14
|
bdstone914 Group: Members Posts: 4,512 Joined: 8-November 03 From: Riverside CA Member No.: 1,319 |
There is an $80 one nut it is not made right and you can not install all the tin on a Type IV motor with out interference. The expensive one is made correct. I have the cheap one and it works.
|
mb911 |
Nov 19 2017, 12:33 PM
Post
#15
|
914 Guru Group: Members Posts: 6,802 Joined: 2-January 09 From: Burlington wi Member No.: 9,892 Region Association: Upper MidWest |
I posted for sale on pelican and sold right away so I guess it was too cheap but either way I am happy for the help..
|
Lo-Fi Version | Time is now: 23rd April 2024 - 03:02 AM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |