Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

> Call out to sbc converted teener owners, Harmonic balancer and timing marks
HalfMoon
post Mar 15 2018, 09:25 AM
Post #1


Senior Member
***

Group: Members
Posts: 828
Joined: 13-November 12
From: Shenandoah Junction, WV
Member No.: 15,144
Region Association: MidAtlantic Region



Owning a Renegade converted sbc 914, I've often wondered how other owners have solved the problem of not being able to see the timing marks on the harmonic balancer.
What was/is your solution (other than timing by ear)?
Thanks!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
 
Reply to this topicStart new topic
Replies
FL000
post Mar 15 2018, 11:15 AM
Post #2


Member
**

Group: Members
Posts: 394
Joined: 31-January 12
From: Lancaster, CA
Member No.: 14,076
Region Association: Southern California



I got a tip from here to mark TDC on the flywheel as viewed from the inspection area on top of the trans. Have yet to fire it up and test it but sounded like a good idea. Should be enough space from engine deck lid area to shine timing light and use remote camera to check it. I asssume a timing light with an advance function is necessary since I won’t have degree marks on the case (just location of TDC).
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
HalfMoon
post Mar 16 2018, 08:24 AM
Post #3


Senior Member
***

Group: Members
Posts: 828
Joined: 13-November 12
From: Shenandoah Junction, WV
Member No.: 15,144
Region Association: MidAtlantic Region



QUOTE(FL 000 @ Mar 15 2018, 12:15 PM) *

I got a tip from here to mark TDC on the flywheel as viewed from the inspection area on top of the trans. Have yet to fire it up and test it but sounded like a good idea. Should be enough space from engine deck lid area to shine timing light and use remote camera to check it. I asssume a timing light with an advance function is necessary since I won’t have degree marks on the case (just location of TDC).


Scott with Renegade suggested the same but I found (on my 73) that the wall comes right exactly over the top transaxle hole.
Opening a panel didn't allow the ability to see the flywheel and it can't be seen from above (behind the dizz) even with the rear rubber shelf removed....so that solution (at least on the 73 where the body in the trunk is slightly different than earlier models) isn't going to work.
The only other thing I could see for using the flywheel as a timing mark is to remove the entire trunk wall and install a shock brace. More work than I'd like for this particular problem.
I've decided to remove the inner metal front shelf (that is apparently only for holding the forward rubber "shelf") behind the access panel I created in the cockpit which should give access to the harmonic balancer. It'll take two people to time the car with this fix, but at least precision timing will be able to occur (I'm re-curving my dizzy, so timing marks are pretty important)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post

Posts in this topic


Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



- Lo-Fi Version Time is now: 17th May 2024 - 02:59 AM