 Is there a "how to.." for crank measurement, and bearing verification? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| malcolm2 |
 Dec 16 2019, 11:07 PM
Post
#1
|
|
Advanced Member  Group: Members Posts: 2,738 Joined: 31-May 11 From: Nashville Member No.: 13,139 Region Association: South East States 
 |
I am gonna make a 2 liter from my 1.8. So I have a refreshed 71mm crank that I have been told has been ground to -0.010.
I measured as best as I can with a digital mic and got about 59.66 on the mains and 49.65 on the rod journals. Where can I find the STD specs and ranges ? were they 60 and 50, respectively? Since I know nothing about this crank, how can I verify the 71 mm measurement? |
   |
 
|
Posts in this topic
malcolm2 Is there a "how to.." for crank measurement Dec 16 2019, 11:07 PM
Superhawk996 @malcolm2
My understanding is that this crank th... Dec 17 2019, 06:17 AM malcolm2 YES, It seems that @jtprettyman has passed it on... Dec 17 2019, 08:46 AM malcolm2 How about the 71mm measurement? Not that it matte... Dec 17 2019, 08:51 AM
Superhawk996
How about the 71mm measurement? Not that it matt... Dec 17 2019, 02:13 PM Mark Henry
How about the 71mm measurement? Not that it mat... Dec 17 2019, 11:26 PM Mark Henry I only use STD cranks or standard (under) cranks I... Dec 17 2019, 09:24 AM malcolm2
I only use STD cranks or standard (under) cranks ... Dec 17 2019, 09:48 AM Superhawk996 Also for what it’s worth, I provided this crank ... Dec 17 2019, 02:34 PM malcolm2 OK it passed the hammer test. very high pitched t... Dec 17 2019, 06:30 PM Superhawk996
With my method of measuring last night, I got a ... Dec 18 2019, 08:53 AM malcolm2
With my method of measuring last night, I got a... Dec 18 2019, 10:03 AM Superhawk996
Thanks for your input. I certainly hope you don... Dec 18 2019, 02:58 PM malcolm2 OK, maybe not the super duper accurate tools but I... Dec 21 2019, 02:47 PM Superhawk996
OK, maybe not the super duper accurate tools but ... Dec 21 2019, 07:36 PM Mark Henry Sounds like a lot. If you're right about #4 yo... Dec 21 2019, 03:24 PM malcolm2
Your rods should at least have the big ends done.... Jan 20 2020, 08:59 AM Superhawk996
So question 1: how do you "DO" the rod... Jan 20 2020, 12:41 PM malcolm2 Both micrometers were checked prior to the last me... Dec 23 2019, 10:08 AM Superhawk996
Both micrometers were checked prior to the last m... Dec 23 2019, 10:34 AM malcolm2
3) For hobbyists like myself, Plastigage can ser... Dec 23 2019, 10:44 AM malcolm2 UPDATE>>>>>
Todd is the Director o... Jan 14 2020, 08:38 PM Superhawk996 Rod measurements align a whole lot closer to what ... Jan 15 2020, 06:00 AM jtprettyman @Superhawk996
Yes, these were done with a very n... Jan 15 2020, 08:58 AM malcolm2 Rod Balancing, End-to-end. I also wondered how in... Jan 21 2020, 08:30 AM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 16th April 2024 - 11:50 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.