 single thrust cam bearing, what is this protrusion? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| malcolm2 |
 May 30 2020, 12:57 PM
Post
#1
|
|
Advanced Member  Group: Members Posts: 2,745 Joined: 31-May 11 From: Nashville Member No.: 13,139 Region Association: South East States 
 |
Assembling my engine. I noticed that the cam thrust bearing as a smaller tang. My case does not have the notch.
Since this is a smaller tang, designed a bit different. I am I supposed to tap it in place and let the action of bolting up the case crush it in place? I built a 1911 about 7 years ago, and I do not remember having issues like this. I am pretty sure I bought all my innards from Type4 store back then too. Clark  Notice no notch in the saddle..... ?  |
   |
 
|
Posts in this topic
malcolm2 single thrust cam bearing May 30 2020, 12:57 PM
914Sixer Look at your old bearing shells and see what you h... May 30 2020, 01:07 PM
malcolm2
Look at your old bearing shells and see what you ... May 30 2020, 01:14 PM SirAndy I am I supposed to tap it in place and let the ac... May 30 2020, 02:19 PM Jonathan Livesay
I am I supposed to tap it in place and let the a... May 30 2020, 02:30 PM malcolm2
I am I supposed to tap it in place and let the a... May 30 2020, 08:05 PM dr914@autoatlanta.com the cases have relieved places for the tabs May 30 2020, 02:32 PM malcolm2
the cases have relieved places for the tabs
The... May 30 2020, 08:02 PM 914sgofast2 That won’t crush; it will distort and pinch the ... May 30 2020, 07:11 PM porschetub Tang is to prevent rotation of the bearing,there m... May 30 2020, 07:19 PM malcolm2
Tang is to prevent rotation of the bearing,there ... May 30 2020, 08:15 PM malcolm2 Jake’s video screen shot. NO TANG ON THE THRUST ... May 30 2020, 08:23 PM malcolm2 RE: single thrust cam bearing May 30 2020, 08:24 PM Mark Henry :D
Grind or file the tang off, I do this every b... May 31 2020, 06:57 AM malcolm2 Thanks Mark. Filing was one thought. Glad you conf... May 31 2020, 08:35 AM 930cabman A bit late to the party, I came upon this a few da... Dec 3 2021, 06:45 PM KSCarrera
And why the single thrust bearing?? Another vict... Dec 4 2021, 06:03 AM Montreal914
Is the type4 store the only source? Dec 4 2021, 11:33 AM Mark Henry
A bit late to the party, I came upon this a few d... Dec 5 2021, 08:59 AM Shivers RE: single thrust cam bearing Dec 4 2021, 12:21 PM zig-n-zag VW made these cam thrust bearings with a copper-im... Dec 4 2021, 09:12 PM Jack Standz Normally, it's less $ to buy two sets of... Dec 5 2021, 12:01 PM 930cabman I used a tiny (3/8" diameter) Dremel cut off ... Dec 5 2021, 12:42 PM Superhawk996 Nice! Minimizes risk of unwanted rotation. Dec 5 2021, 12:44 PM Mark Henry
Nice! Minimizes risk of unwanted rotation.
S... Dec 6 2021, 12:25 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st May 2024 - 09:57 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.