Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

> How much torque is too much?, Removing fan yoke
ctc911ctc
post Aug 1 2020, 02:08 PM
Post #1


Senior Member
***

Group: Members
Posts: 885
Joined: 9-June 18
From: boston
Member No.: 22,206
Region Association: North East States



‘74 2.0 22k

While I wait for the dog teeth to be delivered, I thought I would change the seals (front and rear)

Attached Image

I built a tool for my wheel puller - have turned it to about 80 ft/lbs, kinda worried to crank it another turn,,,,,,

I am using penetrating oil on the shaft,,,,,,,,,what next?

Heat?

Incantations?

Ideas?

(IMG:style_emoticons/default/confused24.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post

Posts in this topic
ctc911ctc   How much torque is too much?   Aug 1 2020, 02:08 PM
Superhawk996   Heat. A rap on the side of the hub while it's...   Aug 1 2020, 02:18 PM
ctc911ctc   Super Hawk to the rescue! Heat and hammer...   Aug 1 2020, 02:23 PM
ctc911ctc   Lots of heat and hammer, no joy yet,,,, over night...   Aug 1 2020, 03:21 PM
pilothyer   If you heat it up with a MAPP torch with it under ...   Aug 1 2020, 03:32 PM
ctc911ctc   Ahhhhh I only have a propane torch,,,,,, will kee...   Aug 1 2020, 03:46 PM
mepstein   Ahhhhh I only have a propane torch,,,,,, will ke...   Aug 1 2020, 04:19 PM
Superhawk996   Ahhhhh I only have a propane torch,,,,,, will ke...   Aug 1 2020, 04:41 PM
porschetub   No ,penetrating oil will have no effect on a taper...   Aug 1 2020, 04:58 PM
porschetub   X2 reply sorry.   Aug 1 2020, 05:02 PM
Jake Raby   These can be tough. They are also getting rare to ...   Aug 1 2020, 06:22 PM
ctc911ctc   Is this the right setup for high and fast heat? h...   Aug 1 2020, 06:53 PM
73-914   Is this the right setup for high and fast heat? ...   Aug 1 2020, 07:15 PM
ctc911ctc   Yikes, I was thinking that I was pulling too hard ...   Aug 1 2020, 06:54 PM
cuddy_k   :agree: with the mapp torch. Two things... 1) whe...   Aug 1 2020, 07:13 PM
76-914   You don't need to buy a torch, just a bottle o...   Aug 1 2020, 07:16 PM
bretth   I have not done this yet myself, but when hitting ...   Aug 2 2020, 12:15 AM
Frankvw   I also had the same issue on my type4 2.0L bus eng...   Aug 2 2020, 07:32 AM
ctc911ctc   Buying MAPP gas now, I do not need O2 as in the pi...   Aug 2 2020, 07:41 AM
Superhawk996   Buying MAPP gas now, I do not need O2 as in the p...   Aug 2 2020, 08:42 AM
ctc911ctc   Hit it with the mapp torch for 60 sec, hammered ar...   Aug 2 2020, 09:00 AM
sixnotfour   Is the puller going through the bore of the flange...   Aug 2 2020, 09:35 AM
ctc911ctc   I have 6 pullers of various size, this puller has ...   Aug 2 2020, 11:12 AM
sixnotfour   I have 6 pullers of various size, this puller has...   Aug 2 2020, 11:18 AM
Superhawk996   Yowza -- can see deformation of the hub from the h...   Aug 2 2020, 10:18 AM
ctc911ctc   OK, more heat - less hammer! BTW, the marks t...   Aug 2 2020, 11:16 AM
sixnotfour   https://www.youtube.com/watch?v=DZU_-BLDNAU DZU_-...   Aug 2 2020, 10:43 AM
cuddy_k   At least 5 minutes I would say, but @superhawk996...   Aug 2 2020, 10:56 AM
cuddy_k   double post   Aug 2 2020, 10:56 AM
Superhawk996   :D Like the video and special tool. The princip...   Aug 2 2020, 10:57 AM
sixnotfour   I shouldn't even respond ..but..my motto.. typ...   Aug 2 2020, 11:02 AM
Superhawk996   I shouldn't even respond ..but..my motto.. ty...   Aug 2 2020, 11:11 AM
bobboinski   I have been successful doing this by getting the p...   Aug 2 2020, 11:31 AM
bobboinski   I just looked back at your puller. I use a steerin...   Aug 2 2020, 11:40 AM
ctc911ctc   :shoot2kill: HEAT, MORE HEAT :shoot2kill: W...   Aug 2 2020, 03:38 PM
porschetub   :shoot2kill: HEAT, MORE HEAT :shoot2kill: ...   Aug 2 2020, 05:38 PM
Superhawk996   Well it came off, :Qarl: :cheer:   Aug 3 2020, 06:29 AM
bobboinski   :beer2: No opinion on the plugs, I cleaned mine u...   Aug 2 2020, 05:02 PM


Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



- Lo-Fi Version Time is now: 29th March 2024 - 08:11 AM