 Master Cylinder Installation, 2 Quick Questions |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Craigers17 |
 Sep 18 2020, 03:22 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 728 Joined: 5-August 17 From: Rome, GA Member No.: 21,317 Region Association: South East States 
 |
So I'm in the processing of re-installing my master cylinder, brakes etc. I had to take the 90 degree fitting off of the old master cylinder & use on the new one. My questions are:
1. Is there a washer or gasket that goes between the main M/C body and the fitting or just a washer between the 2 parts of the fitting? 2. There is a hole for the fluid to flow through in both the fitting body and the piece that pivots around it, for each of the front brakes. My question is do these 2 holes have to line up? My guess is they don't, but just wanted to double check before I install this beast....I really don't want to do this twice. I hope I have explained this accurately,...I'm just referring to the front brake splitter for lack of a better term, ...not the feed lines to the reservoir. I do realize that I need a washer below the rubber grommets where the feed lines go. Thanks for your help.  |
   |
 
|
Posts in this topic
Craigers17 Master Cylinder Installation Sep 18 2020, 03:22 PM
mankowski I don't think the MC's come new with those... Sep 18 2020, 04:36 PM mepstein @Eric_Shea
:beer2: Sep 18 2020, 06:08 PM Craigers17 Thanks for the responses. I think I'm over-an... Sep 18 2020, 06:37 PM
ri914
Thanks for the responses. I think I'm over-a... Sep 18 2020, 06:54 PM bdstone914 Yes you need a crush washer on both sides of the v... Sep 19 2020, 07:30 AM ri914
Yes you need a crush washer on both sides of the ... Sep 19 2020, 08:06 AM Craigers17 Thanks for the replies and information gentlemen... Sep 19 2020, 08:23 AM stownsen914 As mentioned above, you do need washers on both si... Sep 19 2020, 01:41 PM IronHillRestorations Yes you need a copper sealing ring on both sides o... Sep 19 2020, 07:00 PM bdstone914 @[url=http://www.914world.com/bbs2/index.php?showu... Sep 20 2020, 08:14 AM IronHillRestorations The aluminum are for oil line fittings. I’d only... Sep 20 2020, 09:32 AM Craigers17
The aluminum are for oil line fittings. I’d onl... Sep 20 2020, 11:21 AM RichPugh
Thats the move. I have my tank out currently to ... Sep 20 2020, 07:55 PM VaccaRabite
Thats the move. I have my tank out currently to... Sep 21 2020, 01:05 PM Eric_Shea 10x16 and 14x16 Copper Gaskets go on the banjo bol... Sep 25 2020, 05:03 PM Craigers17
10x16 and 14x16 Copper Gaskets go on the banjo bo... Sep 26 2020, 03:27 AM ndfrigi
10x16 and 14x16 Copper Gaskets go on the banjo bo... Sep 30 2020, 03:58 PM MartyYeoman The best way I've found to install the two res... Sep 26 2020, 07:48 PM Craigers17
The best way I've found to install the two re... Sep 27 2020, 04:22 AM Craigers17 Got the m/c and pedal cluster installed. I still ... Sep 27 2020, 12:19 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 29th April 2024 - 11:57 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.