 Cut slot in bell housing, ability to turn engine |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| 930cabman |
 May 17 2021, 06:15 PM
Post
#1
|
|
Advanced Member  Group: Members Posts: 3,064 Joined: 12-November 20 From: Buffalo Member No.: 24,877 Region Association: North East States 
 |
I can find no easy way to turn the engine in small increments as needed to adjust valves, static spark timing, etc. Spark plugs removed to relieve compression of course. It seems to make sense to cut a small ( 3/8 x 1/2") slot in the bell housing to allow for a screwdriver to engage with the ring gear for small adjustments.
Have a fallen off my rocker? thanks |
   |
 
|
  |
Replies
| SirAndy |
May 18 2021, 11:03 AM
Post
#2
|
|
Resident German Group: Admin Posts: 41,641 Joined: 21-January 03 From: Oakland, Kalifornia Member No.: 179 Region Association: Northern California |
As said above, put the rear in the air, car in gear, lock one wheel (with a bar etc) and turn the other ...
(IMG:style_emoticons/default/smile.gif) |
|
|
|
| 930cabman |
May 18 2021, 12:14 PM
Post
#3
|
|
Advanced Member Group: Members Posts: 3,064 Joined: 12-November 20 From: Buffalo Member No.: 24,877 Region Association: North East States
|
QUOTE(SirAndy @ May 18 2021, 11:03 AM)  As said above, put the rear in the air, car in gear, lock one wheel (with a bar etc) and turn the other ... (IMG:style_emoticons/default/smile.gif) Thanks Andy, but in this case the engine/tranny are on a bench for testing. In the future I will use your method when everything is assembled. |
|
|
|
| GregAmy |
May 18 2021, 01:03 PM
Post
#4
|
|
Advanced Member Group: Members Posts: 2,302 Joined: 22-February 13 From: Middletown CT Member No.: 15,565 Region Association: North East States
|
QUOTE(930cabman @ May 18 2021, 01:14 PM) Thanks Andy, but in this case the engine/tranny are on a bench for testing. In the future I will use your method when everything is assembled. Use a prybar in the starter hole. Piece o' cake to R&R the starter, especially on the bench. |
|
|
|
Posts in this topic
930cabman Cut slot in bell housing May 17 2021, 06:15 PM
ClayPerrine Use a 13mm socket on an extension in the center of... May 17 2021, 08:43 PM
930cabman
Use a 13mm socket on an extension in the center o... May 18 2021, 04:04 AM Spoke
Use a 13mm socket on an extension in the center ... May 23 2021, 07:14 AM rgalla9146 4 cyl. ?
Plugs out
trans in 1st gear
... May 17 2021, 08:59 PM rjames It wouldn't work for adjusting the valves, but... May 17 2021, 09:04 PM Superhawk996 Note on turning crank nose / fan hub bolt. Turn i... May 18 2021, 06:10 AM GregAmy Word of warning...that 13mm hub bolt is not design... May 18 2021, 06:53 AM 930cabman
Word of warning...that 13mm hub bolt is not desig... May 18 2021, 12:18 PM brant There is also an $9 remote starter switch fro... May 18 2021, 09:56 AM 930cabman
Thanks Andy, but in this case the engine/tranny ... May 18 2021, 01:13 PM Mark Henry If the engine is out I would re-mark the fan so it... May 18 2021, 01:00 PM 930cabman
If the engine is out I would re-mark the fan so i... May 18 2021, 01:12 PM VaccaRabite I've done a good bit of playing with engines o... May 18 2021, 01:43 PM 930cabman I ended up installing the alternator with associat... May 22 2021, 05:46 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 18th May 2024 - 03:07 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.