 CV joint help needed please, bearings out of position - fell out now what? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| DRPHIL914 |
 Sep 13 2021, 03:20 PM
Post
#1
|
|
Dr. Phil  Group: Members Posts: 5,759 Joined: 9-December 09 From: Bluffton, SC Member No.: 11,106 Region Association: South East States 
 |
so while installing the motor and transmission yesterday- and it seemed to go so smooth, the cv and axle got out of position, the inner must have gotten bumped and twisted , so i was just now trying to get the one that fell out back in , but also noticed they if i spin the axle the outer one is kind of off center as well, so now i am wondering if i am going to have to pull the whole axle to get these put back in the cage and on the axle?? seems like i will have to pull the whole assembly, to get them circlip off and put it all back together properly—-
pandora’s box here - opening a can of worms- i have to put it on the ground to take off the outer axle nut, then pull the shaft right? looks like there is not enough room to pull it with He in and that will have to be pulled too! - can i leave the other side all hooked up? Advice please!! Phil |
   |
 
|
Posts in this topic
DRPHIL914 CV joint help needed please Sep 13 2021, 03:20 PM
brant I never pull the stud to get the cv shaft out
You ... Sep 13 2021, 03:25 PM
DRPHIL914
I never pull the stud to get the cv shaft out
You... Sep 13 2021, 03:40 PM brant yes....
and I have to loosen 2....
then take the ... Sep 13 2021, 03:51 PM DRPHIL914
yes....
and I have to loosen 2....
then take the... Sep 13 2021, 04:29 PM jcd914 I would probably try to find a couple phillips scr... Sep 13 2021, 04:40 PM DRPHIL914 ok tried that no luck, looks like i am going to ha... Sep 13 2021, 05:02 PM iankarr Probably better at this point to just remove the c... Sep 13 2021, 05:07 PM Superhawk996
Probably better at this point to just remove the ... Sep 13 2021, 06:08 PM DRPHIL914
Probably better at this point to just remove the... Sep 13 2021, 06:30 PM brant I use a long tire bar
With a slight bend in n the ... Sep 13 2021, 05:23 PM DRPHIL914
I use a long tire bar
With a slight bend in n the... Sep 13 2021, 06:06 PM brant Maybe soaking with Kroil? Overnight…. Sep 13 2021, 06:52 PM DRPHIL914
Maybe soaking with Kroil? Overnight….
i will... Sep 13 2021, 07:48 PM SirAndy That's some really odd discoloration on that C... Sep 13 2021, 11:02 PM DRPHIL914
That's some really odd discoloration on that ... Sep 14 2021, 07:36 AM jcd914 I think that discoloration is from the heat treati... Sep 14 2021, 12:56 AM SirAndy I think that discoloration is from the heat treati... Sep 14 2021, 10:23 AM falcor75 I use a two foot piece of angle iron that I have d... Sep 14 2021, 03:04 AM mepstein Phil - If you can see pitting or feel ridges with ... Sep 14 2021, 10:44 AM DRPHIL914
Phil - If you can see pitting or feel ridges with... Sep 14 2021, 12:02 PM iankarr Arent' those pretty deep grooves in the last p... Sep 14 2021, 12:53 PM DRPHIL914
Arent' those pretty deep grooves in the last ... Sep 14 2021, 09:33 PM 930cabman I have a couple, one failed completely (with a cra... Sep 14 2021, 01:40 PM bkrantz
I have a couple, one failed completely (with a cr... Sep 14 2021, 07:52 PM Geezer914 PMB performance has CV joints but you have to enla... Sep 14 2021, 05:45 PM rjames You've gone far enough to know you don't w... Sep 14 2021, 08:56 PM DRPHIL914
PMB performance has CV joints but you have to enl... Sep 14 2021, 09:38 PM DRPHIL914 tools for getting the castle nut off, and holding ... Sep 14 2021, 09:47 PM DRPHIL914 all done Sep 14 2021, 09:51 PM Superhawk996 :trophy: Sep 15 2021, 04:30 AM iankarr Nice! Good work! Sep 15 2021, 01:22 PM KELTY360 Happy ending!!…..well, at least a 914 ha... Sep 15 2021, 03:42 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 28th April 2024 - 10:43 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.