 Another 6 external oil cooler thread, Yes I have been reading build threads |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| nditiz1 |
 Jun 5 2022, 08:14 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,188 Joined: 26-May 15 From: Mount Airy, Maryland Member No.: 18,763 Region Association: MidAtlantic Region 
 |
Ok so the temps in the 6 are not what I'd like them to be. Could it be tuning maybe, but the 2.4 is running pretty good and the WB says I'm on the rich side.
I purchased a Mocal t stat. I had already purchased a stock 911 one, but it's bulky so I think I'll sell it. Why do some run the lines up the passenger and some up the driver? Is it because the cooler up front only goes one-way? Just preference? Where is the best mounting spot? Pics would be helpful. Andy put his inside the chassis. I'm looking for a more general mounting spot. Can it be installed up in the frunk as I have seen on others? What's the drawback there? Thanks and sorry in advance for the millionth ask. I might do something similar to tomeric, but was just curious about these other things first. |
   |
 
|
Posts in this topic
nditiz1 Another 6 external oil cooler thread Jun 5 2022, 08:14 PM
SirAndy Just a general observation, but a 2.4L (unless it... Jun 5 2022, 10:07 PM
ClayPerrine
Just a general observation, but a 2.4L (unless it... Jun 6 2022, 06:02 AM jd74914 Not what you asked, but definitely double and trip... Jun 6 2022, 04:45 AM mb911 One other thing to think about and I have personal... Jun 6 2022, 05:13 AM IronHillRestorations Perry’s rear fender oil cooler install
Jun 6 2022, 05:49 AM nditiz1 So I was thinking about this while reading up on a... Jun 6 2022, 05:52 AM SirAndy Temps do not get super high ~210 - 220, BUT this i... Jun 6 2022, 09:10 AM Superhawk996
Temps do not get super high ~210 - 220, BUT this ... Jun 6 2022, 09:23 AM Superhawk996 Just can't figure out for the life of me why t... Jun 6 2022, 07:25 AM nditiz1
Just can't figure out for the life of me why ... Jun 6 2022, 07:49 AM Superhawk996
I would like pressures to be 1bar:1k when hot, te... Jun 6 2022, 08:37 AM mlindner I would install the air diffuser and how are you c... Jun 6 2022, 07:35 AM mskala A few years back I did some experiments under ... Jun 6 2022, 08:08 AM Superhawk996 I'm going to tell you a long story as quickly ... Jun 6 2022, 08:12 AM mb911
I'm going to tell you a long story as quickly... Jun 6 2022, 08:43 AM nditiz1 Ok so it sounds like the lower flaps could help in... Jun 6 2022, 08:59 AM Superhawk996
. . . cooling tin is shiny plated.
That real... Jun 6 2022, 09:03 AM nditiz1
. . . cooling tin is shiny plated.
That rea... Jun 6 2022, 09:07 AM Superhawk996
The question is then will the temp continue to ri... Jun 6 2022, 09:06 AM nditiz1
The question is then will the temp continue to r... Jun 6 2022, 09:14 AM nditiz1 Speed for me was ~75mph. I believe RPM ~3400. I ... Jun 6 2022, 09:46 AM Superhawk996
Speed for me was ~75mph. I believe RPM ~3400. I... Jun 6 2022, 09:53 AM nditiz1 So my cooler was not tested. It looked clean. I ... Jun 6 2022, 10:04 AM porschetub
So my cooler was not tested. It looked clean. I... Jun 6 2022, 03:04 PM mb911
So my cooler was not tested. It looked clean. ... Jun 6 2022, 03:12 PM mb911
So my cooler was not tested. It looked clean. I... Jun 6 2022, 03:11 PM Cairo94507 Here is what my 6 has for an oil cooler in additio... Jun 6 2022, 02:37 PM nditiz1 Air diffuser is should be in place. I say should b... Jun 6 2022, 04:49 PM mb911
Air diffuser is should be in place. I say should ... Jun 6 2022, 05:31 PM nditiz1 I bought one for each side, not sure why as I will... Jun 6 2022, 06:08 PM mb911
I bought one for each side, not sure why as I wil... Jun 6 2022, 06:23 PM mskala Reading deeper about how you're not totally su... Jun 6 2022, 07:22 PM nditiz1 The serial number on the case matches 73.5 CIS eng... Jun 6 2022, 07:37 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 18th May 2024 - 01:13 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.