 new 914 with Gearbox Issues |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| tonybolony |
 Sep 17 2022, 09:11 AM
Post
#1
|
|
Newbie  Group: Members Posts: 30 Joined: 17-September 22 From: Enland , Wes Yorkshire Member No.: 26,859 Region Association: None  |
So new oener here , messing with my 1972 car , i have noticed that i dont seem to have 4/5 gear , i did mess and i ended up loosing Reverse , so am starting to lose the will to live lol, is there a guide on setting up linkages ? i also notice my shifter doent seem to go to the right much also, not sure if thats part of the problem ? but too travel left its got loads and its springs back also ?
confused i am lol |
   |
 
|
  |
Replies
| Shivers |
Sep 18 2022, 09:55 AM
Post
#2
|
|
Senior Member Group: Members Posts: 2,368 Joined: 19-October 20 From: La Quinta, CA Member No.: 24,781 Region Association: Southern California |
Sorry about the dirt and grease. Been parked for a few years in the dirt. Luckily I have not pulled the engine yet. The adjustment is correct in this pic (yellow), was shifting fine. That is your up and down. The side to side will get the paddle at the end of the ball far enough to the left to reach 4-5th gear, paddle needs to push the cage over. But move it too much and say goodbye to 1st- R. I would loosten the fasteners on the mount so with a bump of a rubber mallot it would move but not so loose I'd lose the adjustment I had on up and down. Real small moves till you have it.
I hope this makes sense  |
|
|
|
Posts in this topic
tonybolony new 914 with Gearbox Issues Sep 17 2022, 09:11 AM
emerygt350 Are you playing around with the adjustments in the... Sep 17 2022, 09:19 AM rhodyguy Failed roll pin in the assembly above the rear acc... Sep 17 2022, 11:20 AM PCH Is your gearbox a rear shifter? Just got mine shif... Sep 17 2022, 02:03 PM rjames How are you adjusting it?
If bushings are good, f... Sep 17 2022, 02:35 PM Shivers My 72' is a tail shift. If yours is stock the... Sep 17 2022, 04:06 PM tonybolony wow thank you for all the response , its all new t... Sep 18 2022, 03:18 AM emerygt350 Try checking the cone screw where the rod enters t... Sep 18 2022, 04:35 AM
tonybolony
Try checking the cone screw where the rod enters ... Sep 18 2022, 05:21 AM
ChrisFoley
Try checking the cone screw where the rod enters ... Sep 18 2022, 05:47 AM emerygt350
Try checking the cone screw where the rod enters... Sep 18 2022, 07:36 AM ChrisFoley
[quote name='ChrisFoley' post='3030541' date='Sep... Sep 18 2022, 08:44 AM ChrisFoley There are two plastic balls in that location which... Sep 18 2022, 05:46 AM rgalla9146 Adjustment is done at the rear of the tunnel. Remo... Sep 18 2022, 08:58 AM Dave_Darling You might also use a mirror and flashlight to chec... Sep 19 2022, 03:08 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 6th May 2024 - 07:17 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.