Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

 Forum Rules Classified Rules!
 
 Reply to this topicStart new topic
> FS: 1972 Porsche 914, Willow Green very little rust
BK911
post Aug 31 2023, 03:29 PM
Post #1


Senior Member
***

Group: Members
Posts: 672
Joined: 19-February 04
From: Rocky Top, TN
Member No.: 1,674
Region Association: None
It was a pretty nice little car, and can be again!
Pulled the engine when the clutch pedal went to the floor.
Not exactly sure what happened, but have new cable, throw out bearing, clutch fork, ???
It is NOT running because the engine/tranny are out of the car.
In my ownership, I have:
-Complete suspension rebuild; powder coated everything, new ER rubber bushings, new bearings, new shocks, springs, etc...
-New turbo tie rods
-Brake rebuild; new MC, new rubber lines, rebuilt front calipers. Did not do rear and they could use it.
-Dual empi 40s - have all FI components in box

Needs:
Some minor welding - see pics
new windshield
Engine/tranny installed
Seats work but have tears

I bought from original owner who had repainted in original willow green.
Paint looks pretty good but not perfect.
ODO stopped working but I bought at ~80k miles and drove the crap out of it for ~15 years.
Until clutch broke, drove 1 - 2 times a week 75 mile round trip to/from work.

Engine has pretty good leak down numbers but I forget what they are, around 6 if I remember correctly.

Looking for $20k / best offer as is where is.
Slightly negotiable since it is in project phase.
Just put her on the lift yesterday so I do plan on chipping away to get back to runner status.

Reason for selling - MONEY!! And I need to thin out the herd.

Pics coming in next post...
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
BK911
post Aug 31 2023, 03:38 PM
Post #2


Senior Member
***

Group: Members
Posts: 672
Joined: 19-February 04
From: Rocky Top, TN
Member No.: 1,674
Region Association: None
Attached Image

Attached Image

Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
BK911
post Aug 31 2023, 03:39 PM
Post #3


Senior Member
***

Group: Members
Posts: 672
Joined: 19-February 04
From: Rocky Top, TN
Member No.: 1,674
Region Association: None
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
BK911
post Aug 31 2023, 03:41 PM
Post #4


Senior Member
***

Group: Members
Posts: 672
Joined: 19-February 04
From: Rocky Top, TN
Member No.: 1,674
Region Association: None
Attached Image

Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
BK911
post Aug 31 2023, 03:42 PM
Post #5


Senior Member
***

Group: Members
Posts: 672
Joined: 19-February 04
From: Rocky Top, TN
Member No.: 1,674
Region Association: None
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
BK911
post Aug 31 2023, 03:44 PM
Post #6


Senior Member
***

Group: Members
Posts: 672
Joined: 19-February 04
From: Rocky Top, TN
Member No.: 1,674
Region Association: None
Attached Image

Attached Image


These were from this week, except for the TOTD pic.
Will take more if necessary, but she is a very solid car with only a few spots that need attention.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
BK911
post Sep 20 2023, 03:22 PM
Post #7


Senior Member
***

Group: Members
Posts: 672
Joined: 19-February 04
From: Rocky Top, TN
Member No.: 1,674
Region Association: None
Attached Image

Slowly making progress.
Welding and skim coat done.
Need final sanding and paint.

Going to replace speedo and clutch cable then get engine/tyranny back in car.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
BK911
post Sep 21 2023, 07:37 AM
Post #8


Senior Member
***

Group: Members
Posts: 672
Joined: 19-February 04
From: Rocky Top, TN
Member No.: 1,674
Region Association: None
I think it turned out pretty good.
Almost ready for primer and paint.

Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
BK911
post Sep 21 2023, 07:40 AM
Post #9


Senior Member
***

Group: Members
Posts: 672
Joined: 19-February 04
From: Rocky Top, TN
Member No.: 1,674
Region Association: None
Outer rockers blasted and powder coated ready for installation.

Attached Image



User is offlineProfile CardPM
Go to the top of the page
+Quote Post
BK911
post Apr 18 2024, 02:14 PM
Post #10


Senior Member
***

Group: Members
Posts: 672
Joined: 19-February 04
From: Rocky Top, TN
Member No.: 1,674
Region Association: None
Just finished up another project and lift is coming available.
Thought I'd bump this before I pull in garage and work on her some more.
So....

Bump!!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
« Next Oldest · FS/WANTED: 914 Cars and Rollers · Next Newest »
 

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 

Display Mode: Standard · Switch to: Linear+ · Switch to: Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

- Lo-Fi Version Time is now: 1st May 2024 - 08:38 PM
Invision Power Board v9.1.4 © 2024  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...