 Clutch Tube reweld???, AA says to do it.... |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| tracks914 |
 Aug 18 2005, 02:59 PM
Post
#1
|
|
Canadian Member  Group: Benefactors Posts: 2,083 Joined: 15-January 03 From: Timmins, Ontario, Canada Member No.: 153 Region Association: None   |
I find that I have to keep tightening my clutch every couple of weeks. In an AA catalogue, one of their little window box tips says that if this happens then you need to reweld your clutch tube.
Is this true? Where is the clutch tube located? tx |
   |
 
|
Posts in this topic
tracks914 Clutch Tube reweld??? Aug 18 2005, 02:59 PM
balljoint I have seen a number of cars which have had a smal... Aug 18 2005, 03:59 PM ThinAir914 Here's the procedure: Step by Step Clutch Tube... Aug 18 2005, 04:16 PM Andyrew Take your shifter out, look down, and depress the ... Aug 18 2005, 04:40 PM rhodyguy with my luck i would drill right through the cente... Aug 18 2005, 04:53 PM Mueller Ernies repair is pretty extream, I guess it depend... Aug 18 2005, 04:54 PM tracks914 Is there a post here from Brad and his repair?
(Ju... Aug 18 2005, 04:59 PM rhodyguy i'm pulling my shifter after i get back from t... Aug 18 2005, 05:04 PM Hammy http://www.914world.com/bbs2/html/... Aug 18 2005, 05:09 PM Mueller Aug 18 2005, 05:13 PM Hammy Damn.
Damn those half-ass PO's http://www.914w... Aug 18 2005, 05:34 PM ThinAir914 I originally posted mine because I figured my repa... Aug 18 2005, 05:47 PM rhodyguy a little http://www.914wor... Aug 18 2005, 06:02 PM ThinAir914 Here's Brad's thread. I searched for "Clu... Aug 18 2005, 06:12 PM jkeyzer I think the clutch tube should be nominated for #1... Aug 18 2005, 06:28 PM rhodyguy ok. in b's thread the 2 outer holes are to loc... Aug 18 2005, 07:18 PM Cap'n Krusty <... Aug 18 2005, 07:32 PM scottb so i pull the carpet so i can make the cuts for th... Aug 18 2005, 07:34 PM SirAndy Aug 18 2005, 08:02 PM tracks914 Has anyone tried a small "U" bolt? It would be str... Aug 18 2005, 08:12 PM flesburg 1. The clutch cable tube needs to be held so that ... Aug 18 2005, 08:17 PM tracks914 Looking at Brad's pictures it appears there is... Aug 18 2005, 08:21 PM Mueller hopefully Bowlsby will see this and post pictures.... Aug 18 2005, 08:28 PM itsa914 <... Aug 18 2005, 09:21 PM scottb i have been looking for an excuse to buy a welder ... Aug 19 2005, 05:05 AM swl welding is beyond the limits of what I want to lea... Aug 19 2005, 06:23 AM itsa914 http://www.914world.com/bbs2/h... Aug 19 2005, 07:34 AM ClayPerrine I actually put a u-bolt clamp on Betty's car a... Aug 19 2005, 08:49 AM jonwatts Regardless of the method (I won't poo poo anyo... Aug 19 2005, 09:04 AM scottb with the clarity brought on by careful observation... Aug 19 2005, 08:33 PM tracks914 I'm going to fix mine tomorrow. I will post pi... Aug 19 2005, 09:29 PM ThinAir914 ... Aug 20 2005, 12:57 AM tracks914 Well it's torn down and here is what I'm u... Aug 20 2005, 08:34 AM tracks914 In this pic you can see the fire wall is cracked .... Aug 20 2005, 08:38 AM tracks914 And now I can sandblast the area and build a new s... Aug 20 2005, 08:39 AM SirAndy ... Aug 21 2005, 05:03 PM tracks914 The fixes are in.
3/32 Stainless Steel Plate, cut ... Aug 21 2005, 07:10 PM tracks914 Placed over tubes, a tighter fit than it shows in ... Aug 21 2005, 07:11 PM tracks914 Areas to be welded were sand blasted and welded wi... Aug 21 2005, 07:15 PM tracks914 Front tube was only 1/2 broken. The bottom 1/2 and... Aug 21 2005, 07:20 PM Jeffs9146 You welded it with the gas line in???? You got som... Aug 21 2005, 09:18 PM Jeff Bowlsby Here are the welds Mike Mueller did on my front tu... Aug 21 2005, 10:19 PM tracks914 <... Aug 23 2005, 05:16 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 25th May 2024 - 07:27 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.