For those that care....BAD TUB UPDATE, didit...didit...didit...... |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
For those that care....BAD TUB UPDATE, didit...didit...didit...... |
Joe Bob |
Mar 24 2006, 09:28 AM
Post
#1
|
Retired admin, banned a few times Group: Members Posts: 17,427 Joined: 24-December 02 From: Boulder CO Member No.: 5 Region Association: None |
BAD TUB got the CHP stamp of approval last night......got it's assigned VIN # and I gots my appointment with the BAR (Smog weenies). They want a base line even though it's exempt from smog checks and control.
Took it out on the road last night with an anal probe up the dump tube off of the turbo. Dialed in (as much as possible) the best a/f mix while driving under load.....the wide band 02 meter worked well and I've dialed in 5lbs of boost after putting 500 miles on the new motor......another 500 and I'll try for 8 lbs....anymore and I'll consider an intercooler. Got so excited I waxed my tub last night in the garage under lights....now it's a shiny ten foot paint job... (IMG:http://www.914world.com/bbs2/html/emoticons/dry.gif) After BAR....off to the cretins at DMV and PLATES!!!!!!!!!! |
Trekkor |
Mar 24 2006, 09:35 AM
Post
#2
|
I do things... Group: Members Posts: 7,809 Joined: 2-December 03 From: Napa, Ca Member No.: 1,413 Region Association: Northern California |
(IMG:http://www.914world.com/bbs2/html/emoticons/smilie_pokal.gif)
You think those agenciess are bad. Try dealing with City of Napa building dept. Hold please...( five minutes pass ) " Hi, can I help you?" "Yeah , I'm on hold waiting for an answer" Hold please...( click ) (IMG:http://www.914world.com/bbs2/html/emoticons/headbang.gif) Typical. Glad your project is working out. KT |
Allan |
Mar 24 2006, 11:11 AM
Post
#3
|
Teenerless Weenie Group: Members Posts: 8,373 Joined: 5-July 04 From: Western Mesopotamia Member No.: 2,304 Region Association: Southern California |
Way to go Mike. Hopefully I'll get to see it someday...
|
Howard |
Mar 24 2006, 11:12 AM
Post
#4
|
Incontin(g)ent Member Group: Benefactors Posts: 5,785 Joined: 24-July 03 From: Westlake Village, CA Member No.: 943 Region Association: None |
Trek, Mike is a SB county environmental Nazi. This is just payback time.
|
Joe Bob |
Mar 24 2006, 12:17 PM
Post
#5
|
Retired admin, banned a few times Group: Members Posts: 17,427 Joined: 24-December 02 From: Boulder CO Member No.: 5 Region Association: None |
Howie, buddy, boobala...."nazis" you can't negotiate with....."weenies" you can.
Thus they/me are weenies until they/we become unreasonable.... (IMG:http://www.914world.com/bbs2/html/emoticons/cool_shades.gif) |
alpha434 |
Mar 24 2006, 12:33 PM
Post
#6
|
My member number is no coincidence. Group: Members Posts: 3,154 Joined: 16-December 05 From: Denver, CO Member No.: 5,280 Region Association: Rocky Mountains |
Is this the 356 that you painted with a 2-inch paintbrush?
Why would you turbo it? You can put a chopped down 911 motor in there. Then you've atleast got overhead cams to work with. Kids these days.... (IMG:http://www.914world.com/bbs2/html/emoticons/screwy.gif) |
Aaron Cox |
Mar 24 2006, 01:13 PM
Post
#7
|
Professional Lawn Dart Group: Retired Admin Posts: 24,541 Joined: 1-February 03 From: OC Member No.: 219 Region Association: Southern California |
he has 2 speedsters kid......
one qith a 2.2S motor... and one with a turbo type 1.... |
Mueller |
Mar 24 2006, 01:36 PM
Post
#8
|
||
914 Freak! Group: Members Posts: 17,146 Joined: 4-January 03 From: Antioch, CA Member No.: 87 Region Association: None |
hmmm, have you "priced" a cut-down 911/4 motor?? it's like $20K just for the motor..... |
||
Aaron Cox |
Mar 24 2006, 01:42 PM
Post
#9
|
||||
Professional Lawn Dart Group: Retired Admin Posts: 24,541 Joined: 1-February 03 From: OC Member No.: 219 Region Association: Southern California |
why would we do that? say first, think later (IMG:http://www.914world.com/bbs2/html/emoticons/laugh.gif) |
||||
jd74914 |
Mar 24 2006, 01:58 PM
Post
#10
|
||||||
Its alive Group: Members Posts: 4,780 Joined: 16-February 04 From: CT Member No.: 1,659 Region Association: North East States |
or think naught at all. (IMG:http://www.914world.com/bbs2/html/emoticons/laugh.gif) |
||||||
Porcharu |
Mar 24 2006, 02:06 PM
Post
#11
|
||
Senior Member Group: Members Posts: 1,314 Joined: 27-January 05 From: Campbell, CA Member No.: 3,518 Region Association: Northern California |
Aren't those Suby motors. (IMG:http://www.914world.com/bbs2/html/emoticons/mueba.gif) |
||
Joe Bob |
Mar 24 2006, 05:12 PM
Post
#12
|
Retired admin, banned a few times Group: Members Posts: 17,427 Joined: 24-December 02 From: Boulder CO Member No.: 5 Region Association: None |
License Plates....at last.....smog....woooo nelly, 6.77 CO @ IDLE 10.5 CO @2500 rpms.
8220 ppm and 7683 HC....can you SAY FAT??? (IMG:http://www.914world.com/bbs2/uploads/blog-1143241958.jpg) (IMG:http://www.914world.com/bbs2/uploads/blog-1143241967.jpg) (IMG:http://www.914world.com/bbs2/uploads/blog-1143241975.jpg) (IMG:http://www.914world.com/bbs2/uploads/blog-1143241984.jpg) |
Aaron Cox |
Mar 24 2006, 05:19 PM
Post
#13
|
Professional Lawn Dart Group: Retired Admin Posts: 24,541 Joined: 1-February 03 From: OC Member No.: 219 Region Association: Southern California |
how many gallons of bondo did it take you to mnake the rear lid? (IMG:http://www.914world.com/bbs2/html/emoticons/tongue.gif)
BTW- where is the intercooler going to go??? |
Mueller |
Mar 24 2006, 05:20 PM
Post
#14
|
914 Freak! Group: Members Posts: 17,146 Joined: 4-January 03 From: Antioch, CA Member No.: 87 Region Association: None |
look'n good....going to run some numbers down with a G-tech and so what it puts out??
|
Joe Bob |
Mar 24 2006, 06:16 PM
Post
#15
|
||
Retired admin, banned a few times Group: Members Posts: 17,427 Joined: 24-December 02 From: Boulder CO Member No.: 5 Region Association: None |
Fiberglass and steel, beyotch......bondo is fer ghetto dwellers. (IMG:http://www.914world.com/bbs2/html/emoticons/finger.gif) |
||
MattR |
Mar 24 2006, 06:23 PM
Post
#16
|
||
Advanced Member Group: Members Posts: 3,279 Joined: 23-January 04 From: SF Bay Area Member No.: 1,589 Region Association: Northern California |
and frank (IMG:http://www.914world.com/bbs2/html/emoticons/biggrin.gif) |
||
alpha434 |
Mar 24 2006, 06:26 PM
Post
#17
|
My member number is no coincidence. Group: Members Posts: 3,154 Joined: 16-December 05 From: Denver, CO Member No.: 5,280 Region Association: Rocky Mountains |
Mike, you just chopped a regualr 356 for that, right? Please say that you wouldn't do that to a real speedster. How much dondo did you use in the rest of the car?
And the chopped 911 engines don't cost 20 grand IF YOU DO IT YOURSELF!!! Kids these days. Jeeze. |
Aaron Cox |
Mar 24 2006, 06:30 PM
Post
#18
|
||
Professional Lawn Dart Group: Retired Admin Posts: 24,541 Joined: 1-February 03 From: OC Member No.: 219 Region Association: Southern California |
sorry for the hijack, but there needs to be a humbling beat down of the alphster.... :WHACK: anyway mike - looks mean. you shoulda gone 8's all around (IMG:http://www.914world.com/bbs2/html/emoticons/wink.gif) |
||
alpha434 |
Mar 24 2006, 06:37 PM
Post
#19
|
My member number is no coincidence. Group: Members Posts: 3,154 Joined: 16-December 05 From: Denver, CO Member No.: 5,280 Region Association: Rocky Mountains |
Hey Aaron.
(IMG:http://www.914world.com/bbs2/html/emoticons/finger.gif) Back when I was growing up, I learned that you have to have three times the skill base to play on the level with someone who has twice your pocketbook. I learned that playing paintball. And it carries over everywhere. Cost for Aaron Cox to chop a 6= 20,000$ plus time waiting for it to get done Cost for Alpha to chop a 6=500$ plus time to get it done. Looks like that Vocational degree will pay itself off. (IMG:http://www.914world.com/bbs2/html/emoticons/cool_shades.gif) |
Mueller |
Mar 24 2006, 06:37 PM
Post
#20
|
||
914 Freak! Group: Members Posts: 17,146 Joined: 4-January 03 From: Antioch, CA Member No.: 87 Region Association: None |
you and this "if you do it yourself BS"...how many people can do it or have access to the equipment??? if it was that easy, YOU do it and sell 'em for half that price (IMG:http://www.914world.com/bbs2/html/emoticons/screwy.gif) and even if YOU could do it, you'd end up spending 10K in parts and labor easily.... |
||
Lo-Fi Version | Time is now: 26th May 2024 - 04:29 AM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |