 Help with cutting holes for -6 oil tank., would like to cut holes now while looking for an oil tank. |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| jj83118 |
 Jan 6 2007, 12:22 PM
Post
#1
|
|
Newbie  Group: Members Posts: 33 Joined: 12-May 05 From: Colorado Springs, CO Member No.: 4,066 Region Association: None  |
Help!
I'm in the middle of repairing the longitudinal rust on my 914-6 conversion and I'd like to cut all the required holes for installing a -6 oil tank. I have most of the left rear quarter-panel off and I'd like to cut the holes while I have easy access. I can plainly see where most of the holes should go, but I don't know where to cut the unmarked hole. I could also use some help cutting the required hole in the engine tray sheet metal. Any help is appreciated. Thanks, Jim |
   |
 
|
  |
Replies
| Trekkor |
Jan 26 2007, 11:03 PM
Post
#2
|
|
I do things... Group: Members Posts: 7,809 Joined: 2-December 03 From: Napa, Ca Member No.: 1,413 Region Association: Northern California |
try this.
I believe Dan Root sent me this a couple of years ago. Worked perfect. I doctored it for clarity. The image needs to be 8.5x11, then print. Line up the tank mount hole with the raised filter console boss on the stock 914-4 inner fenderwell, mark for the new hole and cut. KT Attached image(s) 
|
|
|
|
| Tdskip |
Aug 7 2020, 08:53 AM
Post
#3
|
|
Advanced Member Group: Members Posts: 3,686 Joined: 1-December 17 From: soCal Member No.: 21,666 Region Association: None 
|
QUOTE(trekkor @ Jan 27 2007, 12:03 AM)  try this. I believe Dan Root sent me this a couple of years ago. Worked perfect. I doctored it for clarity. The image needs to be 8.5x11, then print. Line up the tank mount hole with the raised filter console boss on the stock 914-4 inner fenderwell, mark for the new hole and cut. KT Blast from the past, but is this still the best template to use printed at 8x11 full size paper?  |
|
|
|
Posts in this topic
jj83118 Help with cutting holes for -6 oil tank. Jan 6 2007, 12:22 PM
mikez
Help!
I'm in the middle of repairing the... Jan 6 2007, 12:53 PM dr914@autoatlanta.com
Help!
I'm in the middle of repairing the... Jan 6 2007, 12:59 PM jj83118 The problem is I don't have the tank yet (I... Jan 6 2007, 03:58 PM mikez Cut the ones you can see, do the finish work later... Jan 6 2007, 04:02 PM GeorgeRud Kudos to the Auto Atlanta templates, they were a p... Jan 6 2007, 04:17 PM
Superhawk996
Only caveat, if you're using an aftermarket ... Aug 7 2020, 09:03 AM thesey914 Didn't Trek have a template file to print off... Jan 24 2007, 04:37 PM Eric_Shea JJ... if you can make the trip you can look at my ... Jan 24 2007, 05:52 PM John I have one of those too. From the same source. Jan 26 2007, 11:12 PM mepstein If you are using Ben’s / 914-6werkshop tank, itâ... Aug 7 2020, 10:43 AM Tdskip
If you are using Ben’s / 914-6werkshop tank, it... Aug 7 2020, 03:22 PM mb911 I suggest templating my tanks to make it even clos... Aug 8 2020, 05:58 AM Tdskip
I suggest templating my tanks to make it even clo... Aug 8 2020, 06:00 AM Mark Henry
I suggest templating my tanks to make it even clo... Aug 8 2020, 12:42 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 17th May 2024 - 01:35 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.