 leaking taco plate..... |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| mike373 |
 Oct 9 2007, 01:49 PM
Post
#1
|
|
Member  Group: Members Posts: 198 Joined: 3-August 05 From: san diego, ca Member No.: 4,536  |
I have taken this darn thing off, cleaned and inspected sealing surfaces over and over again. The gasket is brand new and crush washers. I think it may be distorted, or over tightened at one time. I seem to remember someone making a billet taco plate....????? Could I use loctite 565 in the o-ring???
This is starting to annoy me..... Getting oil all over a brand new engine. Mike |
   |
 
|
| dr914@autoatlanta.com |
Oct 9 2007, 02:22 PM
Post
#2
|
|
914 Guru Group: Members Posts: 8,163 Joined: 3-January 07 From: atlanta georgia Member No.: 7,418 Region Association: None |
QUOTE(mike373 @ Oct 9 2007, 12:49 PM)  I have taken this darn thing off, cleaned and inspected sealing surfaces over and over again. The gasket is brand new and crush washers. I think it may be distorted, or over tightened at one time. I seem to remember someone making a billet taco plate....????? Could I use loctite 565 in the o-ring??? This is starting to annoy me..... Getting oil all over a brand new engine. Mike if it is a fairly new plate, it could be leaking at the poorly welded factory fitting |
|
|
|
| mike373 |
Oct 9 2007, 04:32 PM
Post
#3
|
|
Member Group: Members Posts: 198 Joined: 3-August 05 From: san diego, ca Member No.: 4,536 |
It is leaking at the perimeter.... around the o-ring
|
|
|
|
| SLITS |
Oct 9 2007, 07:26 PM
Post
#4
|
|
"This Utah shit is HARSH!" Group: Benefactors Posts: 13,602 Joined: 22-February 04 From: SoCal Mountains ... Member No.: 1,696 Region Association: None  |
You can try to goop the seal with silicone
or remove it and take it to a machine shop .... lay it on a flat plate, guage plate or whatever they call it and see if it is in fact warped. Maybe they can make it flat again. |
|
|
|
| Spoke |
Oct 9 2007, 07:36 PM
Post
#5
|
|
Jerry Group: Members Posts: 7,158 Joined: 29-October 04 From: Allentown, PA Member No.: 3,031 Region Association: None 
|
QUOTE(SLITS @ Oct 9 2007, 09:26 PM) You can try to goop the seal with silicone (IMG:style_emoticons/default/agree.gif) When I put a taco plate on my 71 for a temp gauge sender, the sucker leaked like crazy. The edge of the plate was hitting the case side so I had to file that down. This helped but didn't stop the leaking. Ended up with gasket sealer on the O-ring and around the bolts. Spoke |
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 14th May 2025 - 08:56 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.