 FROZEN 911 STRUT WEDGE BOLT, HELP! |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| dlestep |
 Dec 26 2008, 02:15 PM
Post
#1
|
|
I am smilin'...  Group: Members Posts: 890 Joined: 15-January 08 From: Sunrise Florida Member No.: 8,573 Region Association: South East States  |
...I've tried to remove the strut wedge bolt with no sucess.
This buggar has refused to show any kind of progress after the drift with a BFH, and a 5 min air drift, that has mucked up the first few threads. I am about to get out the propane torch and heat it up, but I thought that I'd ask you guys first, before it becomes a major surgery and costly recover. Any help is appreciated...Dave |
   |
 
|
Posts in this topic
dlestep FROZEN 911 STRUT WEDGE BOLT Dec 26 2008, 02:15 PM
effutuo101 I did the same a little while ago. I applied heat,... Dec 26 2008, 02:24 PM r_towle heat and pb blaster.
Then, an air chisel works gr... Dec 26 2008, 02:49 PM
dlestep
heat and pb blaster.
Then, an air chisel works g... Dec 26 2008, 02:54 PM r_towle If you turn the wheel all the way in one direction... Dec 26 2008, 03:00 PM dlestep ...The entire front suspension is off, laying in f... Dec 26 2008, 03:07 PM r_towle If you already intend to replace the ball joint, b... Dec 26 2008, 03:14 PM dlestep
If you already intend to replace the ball joint, ... Dec 26 2008, 03:38 PM dlestep ...I have been cycling between drift and air chise... Dec 26 2008, 04:48 PM dlestep
...well as you can see in the photo, I have lost ... Dec 26 2008, 07:24 PM ArtechnikA
...well as you can see in the photo, I have lost... Dec 27 2008, 10:21 AM burton73 Dave,
My 911 wedge bold where also stuck and need... Dec 26 2008, 08:30 PM Wilhelm Sometimes heating it up and applying paraffin acts... Dec 27 2008, 01:12 AM degreeoff
...well as you can see in the photo, I have los... Dec 27 2008, 11:45 AM r_towle Think about taking the lower ball joint nut off...... Dec 27 2008, 12:45 PM rfuerst911sc When you finally get it out do yourself or the nex... Dec 27 2008, 02:35 PM burton73 I could not get the wrench over the round ball joi... Dec 27 2008, 03:12 PM ArtechnikA
I could not get the wrench over the round ball jo... Dec 27 2008, 03:14 PM dlestep ...I wasn't working on it in that condition. T... Dec 27 2008, 03:35 PM 9146986 Soak, heat, bang, repeat as many times as needed. ... Dec 27 2008, 04:04 PM jkp2240 I had same problem. If you have a sazall just saw... Dec 28 2008, 06:11 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 19th May 2024 - 01:57 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.