 first gear replacement, replacing dog tooth - opinions on slider |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| zeezee |
 Feb 21 2009, 06:12 PM
Post
#1
|
|
Member  Group: Members Posts: 115 Joined: 16-October 08 From: san ramon, ca Member No.: 9,651 Region Association: Northern California  |
First is gone ... grinds going in, pops out when I let the clutch out.
I've done lots of linkage adjustments, replacements, etc. etc. Followed the Pelican Tech article to open the tranny and check out the gears. This is what I see... dog tooth:  slider:  I'm assuming I'll be replacing the syncro ring, and the dog tooth gear. And the slider is still ok. Yes? No? Any recommendations on where to pick up the parts? |
   |
 
|
Posts in this topic
zeezee first gear replacement Feb 21 2009, 06:12 PM
Joe Sharp I think you can find a slider for just under ... Feb 21 2009, 07:06 PM J P Stein I'll sell ya a first gear with good dogs ... Feb 21 2009, 07:20 PM Jeff Bowlsby Yay Alan! :D Feb 21 2009, 07:37 PM
zeezee
Yay Alan! :D
Thanks Jeff. But putting it al... Feb 21 2009, 08:46 PM toon1 The back end of the tranny's are not that bad ... Feb 21 2009, 09:41 PM Jeff Bowlsby The factory gasket is better and cheaper than a tu... Feb 21 2009, 10:19 PM Dr Evil Your slider is remarkably in good shape. You can g... Feb 22 2009, 01:07 AM toon1
The factory gasket is better and cheaper than a t... Feb 22 2009, 10:30 AM Cap'n Krusty You DO NOT need any sealer on the nose cover gaske... Feb 22 2009, 10:38 AM Dr Evil Sealer use on the transmission is verboten! No... Feb 22 2009, 10:43 AM zeezee On mine - both the end cap and the intermediate ju... Feb 22 2009, 10:47 AM zeezee
On mine - both the end cap and the intermediate j... Feb 22 2009, 10:50 AM J P Stein The gasket (paper) between the intermediate plate ... Feb 22 2009, 11:26 AM Dr Evil No cork, only paper. They come in various sizes fr... Feb 22 2009, 12:23 PM Jeff Bowlsby I know I have bought the rear cover gaskets separa... Feb 24 2009, 08:26 AM zeezee
I know I have bought the rear cover gaskets separ... Feb 24 2009, 12:52 PM toon1
You DO NOT need any sealer on the nose cover gask... Feb 22 2009, 03:38 PM Dr Evil Reasons:
1- it is unnecessary, the paper seals hav... Feb 22 2009, 05:04 PM PRS914-6 I'm going to disagree with the others. Replac... Feb 22 2009, 05:43 PM Dr Evil With a good band and teeth, I have never had issue... Feb 22 2009, 05:53 PM PRS914-6
With a good band and teeth, I have never had issu... Feb 22 2009, 06:03 PM Dr Evil In the 100+ boxes I have repaired or parted I have... Feb 22 2009, 06:05 PM PRS914-6 Ask for Tom and tell him we talked. He's a pr... Feb 22 2009, 06:25 PM Dr Evil I have talked to Tom many times. He is always stra... Feb 22 2009, 08:12 PM J P Stein These burrs and any others like them need to be fi... Feb 22 2009, 09:43 PM PRS914-6 This is what I look for.....
1. Arrow pointing to... Feb 22 2009, 11:05 PM Dr Evil Ya, the bird has been out of stock on them for a l... Feb 24 2009, 03:15 PM zeezee
Ya, the bird has been out of stock on them for a ... Feb 25 2009, 03:58 PM zeezee I replaced the dogs and the syncro. Put it all tog... Mar 8 2009, 01:03 PM Dr Evil OK, popping out means that either the groove in th... Mar 8 2009, 04:04 PM Joe Ricard Or the shift console fingers are not pushing the 1... Mar 8 2009, 04:32 PM Dr Evil True that. I was assuming that the external stuff ... Mar 8 2009, 04:53 PM zeezee OK - so I put the gears all back together. The fin... Mar 8 2009, 08:20 PM PRS914-6
OK - so I put the gears all back together. The fi... Mar 8 2009, 08:46 PM zeezee
That sounds like way too much. The slider is ty... Mar 8 2009, 09:51 PM PRS914-6
:stooges:
:confused:
Mar 9 2009, 12:56 AM Dr Evil If you remove the bolt, while it is in gear, and a... Mar 8 2009, 10:01 PM zeezee YAY! I was able to adjust the fork so the slid... Mar 8 2009, 10:47 PM zeezee It's all back together - and shifts well.
Tha... Mar 24 2009, 11:56 AM Dr Evil :thumbsup: Mar 24 2009, 12:10 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 17th May 2024 - 03:40 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.