bdstone914
Apr 25 2014, 10:52 PM
I have a new batch of plated hardware.
#1 Spare tire hold hold plate and bolt $15
#2 Charcoal canister strap $20. One silver and one gold
#3 E brake cable assembly $40, ratchet $15
#4 Seat adjuster "comb" $15. curved targa trim clips $15 per pair, Clutch clevis $10
SOLD #5 Torsion bar adjuster screws $10 each
#6 Accelerator rods $15
SOLD #7 Gas tank nipples early of late $20 per pair
#8 Rear upper trunk latches $35, #9 replacement steel cups $10
#10 Front upper or #11 lower latches $30 each
#12 Engine lid latches $20 each
#13 square blower clamp $10,
#14 Sold Brake reservoir clamp $20.
#15 round blower motor clamp
SOLD #16 Gas tank hold down clamp $15 curved targa trim clips $15 per pair
bdstone914
Apr 25 2014, 10:54 PM
E brake cable assembly $40 Ratchet $15
Seat adjuster "comb" $15. curved targa trim clips $15 per pair, Clutch clevis $10
bdstone914
Apr 25 2014, 10:55 PM
Sold Torsion bar adjuster screws $10 each
Accelerator rods $15
bdstone914
Apr 25 2014, 10:56 PM
SOLD Gas tank nipples early of late $20 per pair.
Rear trunk latches $35, replacement steel cups $10
bdstone914
Apr 25 2014, 10:59 PM
Front upper or lower latches $30 each
Engine lid latches $20 each
SOLD Front strut keyed washers $10 per pair. Late type but will fit all years
Luke M
Apr 26 2014, 10:20 AM
pm sent....
gcrotvik
Apr 26 2014, 12:35 PM
Pm sent.
BeatNavy
Apr 26 2014, 01:27 PM
PM sent...
bcheney
Apr 26 2014, 02:06 PM
Payment sent!
Thanks!
Harpo
Apr 26 2014, 06:27 PM
Email sent
sbsix
Apr 26 2014, 06:49 PM
Bruce, I sent you a pm.
bcheney
May 2 2014, 11:25 AM
QUOTE(bcheney @ Apr 26 2014, 04:06 PM)
Payment sent!
Thanks!
Received my order today and everything was exactly as described. Thanks Bruce!
sbsix
May 2 2014, 05:01 PM
Bruce, I received my packet today, thanks. Interesting discovery on the torsion bar adjusting screws; they are different! One is 55 mm and the other is 58 mm long. Same thread pitch and same thread length. The longer of the two has a longer neck, and matches the picture of the adjusting screw Stoddard shows on their parts board with the part #911.341.115.00. My parts book shows part #914.341.115.00 for all years & models of 914s.
I've attached some pictures to show you. Long story short (no pun intended) do you have a 58 mm adjusting screw, plated, that you could sell me so I have a matched set?
I have a 914-6 and checking the parts book shows that the torsion bar adjusting arms have the same part number as a 911 and the 914-4 has a different part number. This is a new one on me.
I'll PM you, as well.
Best,
Gary
sbsix
May 2 2014, 05:02 PM
Another view
Lingcuisine
May 3 2014, 08:26 PM
Pm sent
mdelwiche
May 3 2014, 09:34 PM
Box of goodies came in today and were installed! Thanks again Bruce!
Click to view attachment
Kansas 914
May 6 2014, 07:55 AM
QUOTE(bdstone914 @ Apr 25 2014, 10:52 PM)
I have a new batch of plated hardware.
#2 On tank charcoal canister strap $15.
Hi Bruce,
If this canister strap is still available I will take it.
I also need some other stuff - I will send you a PM.
Thanks!
bdstone914
Jun 7 2014, 07:52 PM
Bump
Many parts still available
koozy
Jun 7 2014, 10:46 PM
Bruce, I'll take a rear trunk latch. Sending PM form payment info
gcrotvik
Jul 14 2014, 08:56 AM
QUOTE(sbsix @ May 2 2014, 04:01 PM)
Bruce, I received my packet today, thanks. Interesting discovery on the torsion bar adjusting screws; they are different! One is 55 mm and the other is 58 mm long. Same thread pitch and same thread length. The longer of the two has a longer neck, and matches the picture of the adjusting screw Stoddard shows on their parts board with the part #911.341.115.00. My parts book shows part #914.341.115.00 for all years & models of 914s.
I've attached some pictures to show you. Long story short (no pun intended) do you have a 58 mm adjusting screw, plated, that you could sell me so I have a matched set?
I have a 914-6 and checking the parts book shows that the torsion bar adjusting arms have the same part number as a 911 and the 914-4 has a different part number. This is a new one on me.
I'll PM you, as well.
Best,
Gary
Hi Gary & Bruce,
I found the matching set.
Bruce, I purchased a set of 911/914-6 torsion bar adjusters and screws from you early this year. They were clear zinc plated. I went to install them this weekend and found the adjuster screws are a different length. I recalled reading this post months ago. Seems as though I have the matching set to Gary's set.
Greg
sbsix
Jul 14 2014, 09:22 AM
Greg, great job, I'll meet you halfway up the coast and we can exchange parts!
gcrotvik
Jul 14 2014, 09:27 AM
QUOTE(sbsix @ Jul 14 2014, 08:22 AM)
Greg, great job, I'll meet you halfway up the coast and we can exchange parts!
No problem! Any excuse to see SB. I grew up in OC and spend many weekends in Santa Barbara. Love it there.
Greg
This is a "lo-fi" version of our main content. To view the full version with more information, formatting and images, please
click here.