bdstone914
Oct 8 2014, 12:13 PM
I have a black 75 and a yellow 74 that are being cut up for parts. Many parts are already gone. The 75 has the front fenders cut off but are still available. The passenger quarter is gone. Not a lot of rust on most of the car.
The yellow 74 car has the passenger fender, rear trunk panel. pedal area and front passenger pan, and firewall cut out.
I can cut out sections as needed. Since a price is required I will say $50 -200. The price depends on the difficulty of cutting out the section and the size.
I can send pictures of specific areas. PM your email address.
And yes there is a good story that goes with the tire in the front trunk of the yellow car.
Bruce
Sleepin
Oct 8 2014, 12:39 PM
Hey Bruce, how is the passenger side cowl, fender seam area on the yellow car? I'm not 100% sure I need to replace mine, but it's close.
ndfrigi
Oct 8 2014, 12:58 PM
Sir, thus the 74 yellow has a good rear passenger side ear suspension? How much ship to 90630? God bless! Noel
Click to view attachmentClick to view attachment
AvalonFal
Oct 8 2014, 01:30 PM
What would LS inner wheel well on the '74 and shipping to 19136 cost? Here's what I'm trying to replace.
Click to view attachment
Brian_Boss
Oct 8 2014, 02:05 PM
If either car has a good front trunk floor i would want that and also the piece of the engine shelf near the battery tray that typically gets cut out for A/C installs. I can take a picture to clarify.
Shipping to 75214
Thanks,
Brian
rstover
Oct 12 2014, 04:19 PM
Click to view attachmentClick to view attachmentQUOTE(Brian_Boss @ Oct 8 2014, 03:05 PM)
If either car has a good front trunk floor i would want that and also the piece of the engine shelf near the battery tray that typically gets cut out for A/C installs. I can take a picture to clarify.
Shipping to 75214
Thanks,
Brian
Looking for front left channel and a small area above and in front of left rear tail light housing
Zinergy69
Oct 12 2014, 10:39 PM
I'm looking for the piece outlined, the shock if in good shape and the gusset just below. PM me with cost... I go to Riverside often, I can pick it up.
Thanks!
Click to view attachment
rohrer914
Oct 13 2014, 09:14 PM
how about the fuel pump hatch door?.
I'm also looking for one engine lid hinge brake.
OllieG
Oct 14 2014, 03:36 AM
Hi Bruce,
How's the rear drivers body panel below the sail panel on the yellow car?…I'm looking for a section between the rear arch and door jamb.
Thanks.
bdstone914
Oct 14 2014, 10:34 AM
QUOTE(rohrer914 @ Oct 13 2014, 08:14 PM)
how about the fuel pump hatch door?.
I'm also looking for one engine lid hinge brake.
The fuel pump cover is sold.
Just by the engine lid bracket new from Restoration designs. They are not that much.
barebrad
Mar 19 2015, 05:12 PM
Are you still cutting? I'm looking for the engine mount bracket under the battery tray?
Let me know if this is available.
bdstone914
Mar 19 2015, 08:30 PM
Pm sent. Yellow 74 is cut into chunks. Black 75 about the same as pictured.
Bruce
shuie
Mar 20 2015, 07:26 AM
I need two of these if you still have them. The channel shaped bracket that is welded to the cross member w/toothed height adjuster. Shipped to 70769 please.
80cap
Mar 20 2015, 07:50 AM
DO YOU HAVE THE 2 REAR TARGA LATCHES
BRIAN
bdstone914
Mar 20 2015, 01:52 PM
QUOTE(80cap @ Mar 20 2015, 06:50 AM)
DO YOU HAVE THE 2 REAR TARGA LATCHES
BRIAN
Yes i have refinished rear targa latches for $60 a pair shipped. Can post a picture later.
914Sixer
Mar 20 2015, 07:07 PM
Bruce,
How is the rear trunk floor on the 75? They are quite a bit different than the early ones.
Jw4129
Feb 13 2018, 10:29 AM
I am lookin for all targa latches...
bdstone914
Feb 13 2018, 04:08 PM
QUOTE(Jw4129 @ Feb 13 2018, 10:29 AM)
I am lookin for all targa latches...
PM sent, BTW this ad id three years old so not much is left from these cars but I have lots of 914 parts.
Nacho
Feb 13 2018, 05:14 PM
Hi Bruce
How much for this area?
Click to view attachmentThanks
VRROOMM1
Feb 17 2018, 11:52 AM
how much for the trunk hinges?
bdstone914
Feb 17 2018, 04:51 PM
QUOTE(VRROOMM1 @ Feb 17 2018, 11:52 AM)
how much for the trunk hinges?
Which ones ? front or rear? $25 shipped for either pair. I have several sets.
Bruce
mgp4591
Feb 18 2018, 08:43 AM
Hey Bruce, how about a solid pedal box?
Thanks, Mike
bdstone914
Feb 18 2018, 09:50 AM
QUOTE(mgp4591 @ Feb 18 2018, 08:43 AM)
Hey Bruce, how about a solid pedal box?
Thanks, Mike
I assume you mean the sheet metal where the pedals install ? I have a parts car with a good section. Send me a picture of the area where you want it cut.
Bruce
To all,
This post is over two years old. Most of the parts on these cars are long gone. I still have three parts cars and can still supply supply many parts.
rick 918-S
Feb 21 2018, 04:04 PM
Do you have a clean right rear floor pan? Fixing a really clean factory 6. Just a few small issues. I would rather piece in a section than use a RD panel.
This is a "lo-fi" version of our main content. To view the full version with more information, formatting and images, please
click here.