Machined here in California, 3mm thick by 20mm tall (.120" x .787")

Can be made larger or smaller, with or without chamfers.

Sorry no pins or studs, these are to be adhered using double stick tape (not supplied)

Prices: $10 per letter or number, for example the 3.0 sample will be $20 plus shipping. The 914-GT will fit in a small USPS flat rate box which is currently $7

Click to view attachment
Click to view attachment
Click to view attachment
Click to view attachment

Great, car is going home, I need ASAP. $27.15? PayPal OK? Check? Send your address. Thanks, Brad

914 Limited Inc.
Brad Mayeur
1162 N. Byerly Hills Dr.
East Peoria, IL. 61611
309-694-1707
P914LTD@yahoo.com

914-6 emblem, 20mm tall
Click to view attachment

Rendering of 914-RS (30mm tall)
Click to view attachment

Nicely done. You have winners here.

A comparison of chamfered edges and non chamfered edges (going to remake the chamfered one here in sample pic, a little too aggressive, really notice on the period)

Click to view attachment
Click to view attachment

I know, the 914-8 looks bent, odd looking picture


Click to view attachment

oh, wow! These are really looking good!!! Thank you for taking them to the next level, they're looking great. :-)

PM sent

email replied to,

I have been looking for something like these items for years. BEHOLD! Available right under my nose.

Mike, sending an email regarding what i want. Need 914-6, 3.2, Carrera.

Knowing the supplier, these will be "first caliber plus"

Steve Hurt

Great work! I might need something similar eventually, like 914 RS or 914 GT.

Did a "large" version of 914-RS last night.

stock is 20mm, this one is 30mm, I still need to deburr this one and clean it up some.

Click to view attachment

Very nicely done...will you kindly make a 914-RS emblem to replace the stock rear unit I have (size wise) please?

Tony

Would like a 914-6 non Cham regular size. Pm sent

PM sent. How do I order? Pay? thx

Sent you a PM.

Are you still actively making these Mike?

Tony

Yes I am , sorry for not looking at the thread like I should!

I will get your 914-RS done this week and send you a picture for your approval.

I put these in my tumbler, I think I like the satin look a tad bit more than polished myself.

Click to view attachment
Click to view attachment

Mike,

Thank you Sir! I will wear your emblem with pride...I want an additional number though as well please. Please advise if this is possible. I also would like a slightly larger chamfer to the edges/radius if possible. I will gladly pay for the hassle...

914-RS with the smaller subset of 7.0 (just like you are displaying the 2.0 examples above).

Tony

No extra charge for the drawing/programming, I do most of that while enjoying daughter/daddy TV time watching the shows we like that the wife wants no part of. (pretty much anything SciFi)

I need an emblem for my 912-6 from 1967.
Can you make it in the same height as än 911 emblem?
Can you send it to Sweden ?

Regards

Niklas Ekström

Yes to all the above. I will send you a PM later in evening.

Mike

Great Service,,,,,,,,,Merry X-mas..to all

Sorry it took so long...glad you like it, my wife got a kick out of that one.

as they say in production world "JIT" no push / no pull... just in time

Mueller,

Really great stuff, I wish I thought of this earlier for a Christmas Tree orniment.

Wondering?
Can you do a one off special emblem like - 911-RS -?? It would be for a good Porsche friend doing his original owner 1964 911-S into a 911-RS clone. Let me know if you can do a special one with an approx. cost $_____?

Merry Christmas to you and family and blessing for good health in 2018

Tom

Was lucky and got a set of these. Amazing look and well done. Very worth while.

Is it possible to be machined out of black plastic sheet?

Like delrin? I see why not, let me see if I have any scrap pieces to practice on.

Just wondering how the emblems are coming. Whenever you have had the time. Work looks great

Steve

Hi Steve,

Sorry for taking so long, here is a picture of your stuff.

Click to view attachment

Looks like exactly what I had in mind. Need to know how you want funds and do you need my address?

Thanks, Mike,; does reflect your many professional level talents.

Steve

Hi Tom,

A little tease, will finish it tomorrow night, just need to cut it out and deburr. Click to view attachment

Mike,
Perfect, I like
Tom

Came out pretty good for a taildragger

Click to view attachment

Finally got around to putting this on. Looks great, Thank you
Click to view attachment

Mike,
Perfect & I really like the size.
Your machining skills are great & the price was reasonable for a custom emblem.
BTW: What kind of material was used on the emblem??
Tom

Thanks for the kind words.

Best information I could find online is that it is 6061....a fellow member had his emblem black anodized and it came out nice.

I hope your friend likes it.

Proposed design for Niklas,

You can ignore the 912-4 , I had that in my mind while programming then came back to this thread to see my mistake.

Click to view attachment
Click to view attachment

Perfect! I take 2 pcs of 912-6


Niklas

Niklas,

Here you go:

Click to view attachment

Please don't forget about my October request...thanks Mike!

Tony

Damn, that long ago? All done, will package it up tonight.

Glad I don't do this for a living, I'd be starving to death.

How much to make a stock looking one that says "4.0"?

$20 plus shipping, you have a PM, thanks Mike

Love my 2.1! Should update to 2.3 but I figured people would see the point when they can’t catch me.

Are you running any engine size emblems in the near future. I need one for a "2.2" engine. Thanks.

Did you ever follow up on black plastic version for those of us wiith later model emblems?

I'd say stick with the aluminum and just paint it satin black. I just painted mine today. You'd have to look pretty close to know it wasn't the stock badge...except mine says 3.3 on it. Will post pics after I hit it with one more coat and it dries.

Here it is. Top one is plastic, bottom is aluminum.

Click to view attachment

It's harder than it looks to get a good pic! Although the 3.3 looks larger it's in the same scale as the other badge. Just the angle of the photo I guess.

These are very nice quality. I would pay 2X what Mike is charging.