Chi-town
Dec 3 2018, 11:13 PM
I'm going to break this thread up to make it easier for people to see what I have
djway
Dec 4 2018, 02:08 AM
Sending PM for more stuff
flyer86d
Dec 4 2018, 04:53 AM
Sail trim please shipped to 05674.
Charlie
Tdskip
Dec 4 2018, 07:31 AM
I don’t remember but interested in front fog light assemblies if you have them.
Let me know if you want help pulling these apart.
EDIT - if rear chrome bumper is driver quality I'd like it (but should probably eyeball it first)
johnvan8
Dec 4 2018, 08:38 AM
I'll take the sunvisors for local pickup. Sending pm.
Chi-town
Dec 4 2018, 09:29 AM
All request replied to
jdamiano
Dec 4 2018, 01:10 PM
I’m looking for one tear free black basket weave seat bottom.
Chi-town
Dec 4 2018, 02:57 PM
No seats sorry
koozy
Dec 4 2018, 09:07 PM
Any fog lights?
Chi-town
Dec 4 2018, 11:11 PM
No fogs
Retroracer
Dec 4 2018, 11:27 PM
DO you have a Tachometer or two available?
- Tony
Tdskip
Dec 5 2018, 07:00 AM
Good morning Dylan, in addition to the other bits how about;
Rear trunk lock - 914 512 913 00
Front bumper rubber block - 914 505 107 10
Front valance stoppers - 914 559 252 10
Sideshifter cover - PCG 424 501 01
76-914
Dec 5 2018, 09:07 AM
Looking for some metal for my next project. Is the rear psg inner fender well good on any of those cars. That's the metal behind the battery. If so, I can come by and cut out the section I'll need. LMK, Kent
ValcoOscar
Dec 5 2018, 09:41 AM
QUOTE(76-914 @ Dec 5 2018, 07:07 AM)
Looking for some metal for my next project. Is the rear psg inner fender well good on any of those cars. That's the metal behind the battery. If so, I can come by and cut out the section I'll need. LMK, Kent
Hey Kent-
If he does and you decide to come up give me a shout...I have a portable plasma cutter that will make this a breeze.
Just need an air source. Maybe Dylan has a compressor?
When I was there a few nights ago I didn't see one.
Oscar
Chi-town
Dec 5 2018, 09:47 AM
@retroracer - 1 Tach available but it needs fully reconditioned, you pay shipping and it's yours.
@Tdskip - Nope, none of the above sorry.
@76-914 - I can cut that section out for you but you'll probably want to come see it first.
@ValcoOscar - is it a 110v or 220v unit? These old houses don't have 220v but I do have an air compressor.
76-914
Dec 5 2018, 10:18 AM
QUOTE(ValcoOscar @ Dec 5 2018, 07:41 AM)
QUOTE(76-914 @ Dec 5 2018, 07:07 AM)
Looking for some metal for my next project. Is the rear psg inner fender well good on any of those cars. That's the metal behind the battery. If so, I can come by and cut out the section I'll need. LMK, Kent
Hey Kent-
If he does and you decide to come up give me a shout...I have a portable plasma cutter that will make this a breeze.
Just need an air source. Maybe Dylan has a compressor?
When I was there a few nights ago I didn't see one.
OscarThx for the offer
@ValcoOscar but I'll probably take a sawzall, an angle grinder and extension cord to do a rough cut.
76-914
Dec 5 2018, 10:20 AM
QUOTE(Chi-town @ Dec 5 2018, 07:47 AM)
@retroracer - 1 Tach available but it needs fully reconditioned, you pay shipping and it's yours.
@Tdskip - Nope, none of the above sorry.
@76-914 - I can cut that section out for you but you'll probably want to come see it first.
@ValcoOscar - is it a 110v or 220v unit? These old houses don't have 220v but I do have an air compressor.
@
Chi-town I can drop by any weekend morning. LMK why works for you.
ValcoOscar
Dec 5 2018, 10:54 AM
QUOTE(Chi-town @ Dec 5 2018, 07:47 AM)
@retroracer - 1 Tach available but it needs fully reconditioned, you pay shipping and it's yours.
@Tdskip - Nope, none of the above sorry.
@76-914 - I can cut that section out for you but you'll probably want to come see it first.
@ValcoOscar - is it a 110v or 220v unit? These old houses don't have 220v but I do have an air compressor.
Sounds like Kent has this covered
but for future reference, either 110v or 220v.
It's a Miller Spectrum 375 X-TREME
Oscar
Chi-town
Dec 5 2018, 11:31 AM
Did some price comparisons, adjusted accordingly.
Retroracer
Dec 5 2018, 08:33 PM
QUOTE(Chi-town @ Dec 5 2018, 07:47 AM)
@retroracer - 1 Tach available but it needs fully reconditioned, you pay shipping and it's yours.
Done! PM me with the shipping price and I'll throw it on PayPal
- Tony
Chi-town
Dec 5 2018, 09:40 PM
I'll send you a pic in the morning just to make sure
Chi-town
Dec 8 2018, 09:13 AM
White 72 coming apart this weekend, no trunk or hood
Chi-town
Dec 12 2018, 10:25 AM
Bump for offers
Tdskip
Dec 12 2018, 01:04 PM
Pictures pictures pictures
second wind
Dec 12 2018, 01:20 PM
QUOTE(Chi-town @ Dec 12 2018, 08:25 AM)
Bump for offers
Do you have a good condition relay board cover? The type with the slant in front? Thank you,
gg
Retroracer
Dec 12 2018, 01:33 PM
Still wanting the tach, gentle reminder. Sent you a PM...
- Tony
Chi-town
Dec 14 2018, 09:16 PM
Replied
Someone asked me about the black plastic tubes that run front to rear for the canister but I can't remember who. If you're still in need of them let me know!
Charles Danek
Dec 16 2018, 10:58 AM
Hi!
I am possibly interested in the following:
- Behr Fresh Air Box (w/ no overspray)
- Brake Fluid Reservoir.
- Wiper assembly if not rusted out.
...and if you are getting out your sawsall...
- Small section of interior door support sheet metal. (PO removed a scoop for speaker install.) Both sides needed. Can send pics of what I need.
- Along the bottom of the frunk, there is a short brace on each side that has two 4"-ish holes in it - this is missing on my car passenger side only. Can send pics of what I need.
LMK --
Thanks in advance!!
Charlie
Chi-town
Dec 17 2018, 03:55 PM
@Charles Danek I have the wiper assembly and the brake reservoir left, all sheet metal is gone
Charles Danek
Dec 18 2018, 01:26 AM
QUOTE(Chi-town @ Dec 17 2018, 02:55 PM)
@Charles Danek I have the wiper assembly and the brake reservoir left, all sheet metal is gone
Cool! How much we talkin for those 2? I live in 91344 Thanks in advance!
Chi-town
Dec 18 2018, 02:38 PM
@Charles Danek $70 for both, I'm about an hour south of you.
housepumpinpc
Dec 19 2018, 05:30 AM
Any fuel injectors? 1.7l...
Chi-town
Dec 19 2018, 10:11 AM
Nope, sorry
Mike Moss
Dec 19 2018, 07:21 PM
Looking for the 90 degree brass brake line fitting. On the line between the master cylinder and line going thru tunnel. Thanks Mike
Chi-town
Dec 19 2018, 07:25 PM
QUOTE(Mike Moss @ Dec 19 2018, 05:21 PM)
Looking for the 90 degree brass brake line fitting. On the line between the master cylinder and line going thru tunnel. Thanks Mike
@Mike Moss I have many, cleaned and ready to go.
Chi-town
Dec 26 2018, 02:29 PM
Adding pics as I get the mess sorted
westo2
Dec 27 2018, 09:03 AM
Do you have the exhaust header bolts available? Looking for the 8 studs and nuts used to bolt the heat exchangers on. Thanks!.
Steve
Dec 28 2018, 01:46 PM
Do you still have the late model white drivers side door?
PM sent
Chi-town
Dec 28 2018, 03:45 PM
@westo2 sorry no engine parts.
@Steve text sent
dereknlee
Dec 28 2018, 09:33 PM
Looking for the sheet metal panel that covers the master cylinder etc. on the underside, for a car built in late '71. Have one?
Chi-town
Dec 28 2018, 11:24 PM
Nope, sorry
bdstone914
Dec 29 2018, 08:15 AM
QUOTE(westo2 @ Dec 27 2018, 09:03 AM)
Do you have the exhaust header bolts available? Looking for the 8 studs and nuts used to bolt the heat exchangers on. Thanks!.
Buy them new. Exhaust hardware is not worth reusing.
Bump
Chi-town
Dec 30 2018, 05:57 PM
More pics added
Bilstein shocks removed, once disassembled found they were toast.
The complete hardware set from them is available
Chi-town
Jan 1 2019, 07:12 PM
More pics and hardware added
Chi-town
Jan 4 2019, 01:14 PM
Today's Special 1-4-19
Early tie rods with newer Febi outers $35
All the undercoating is cleaned off and all the threads are smooth.
Outers are nice and tight.
sbartmess
Jan 4 2019, 08:02 PM
Do you have a front bumper from the 914-6 available?
Chi-town
Jan 4 2019, 10:11 PM
QUOTE(sbartmess @ Jan 4 2019, 06:02 PM)
Do you have a front bumper from the 914-6 available?
I've never had a 914-6, sorry no extra bumpers.
VRROOMM1
Jan 5 2019, 09:30 AM
do you have rear trunk hinges? and how much?
Chi-town
Jan 5 2019, 02:11 PM
Sorry no hinges front or rear
Chi-town
Jan 10 2019, 11:17 AM
Anyone need a later LH door before I scrap it?
This is a "lo-fi" version of our main content. To view the full version with more information, formatting and images, please
click here.