I have a 1973 porsche 914 parts car. The body has been welded together right down the center so it will be parted. This is a list of some of the parts and price's;

Riviera rims in nice condition will remove rubber $160.00 set

Gauge cluster condition unknown 120 mph speedo tach and fuel gauge full set $80

early door glass $25 each

outter door handles really dull or scratched up only good for painting but in solid condition $25 each

pedal assembly $45

front calipers $40 each many sets.

early rear hubs 1970 with extra land for five lug conversions $80

Many other parts available sawzall ready for whatever body parts needed plus shipping on all parts.

I just need the front bumper top (rubber pad). If it in good condition. I will PM you.

how are the tail lights? all bumper dogbones?

where are you located. I need either the front pass fender or the front part of the pass fender at the light bucket.

Sorry bumper rubber shot.

Thanks

Hi,

I am located in Victorville, Ca 92392 I can cut whatever you need fender or bucket $80 on fender or $40 for the hole bucket and headlight assembly.

Thanks

Hi,

Tail light lens are gone but the housings are good.

Thanks

If the left rear fender is in good condition, I'm interested. Thanks!

[quote name='msasnett' date='Oct 29 2008, 12:28 PM' post='1096260']
If the left rear fender is in good condition, I'm interested. Thanks!
[n

Hi,

Left rear fender is in nice shape no dents or rust $80 as much cut needed.

Thanks

Is the wiring harness usable? I need a whole harness plus fuse board. Am doing
carbs so don't need any FI stuff.

Thanks...John

Payment was sent for last night by Pay Pal. Any idea when you will ship them?


SONAUTO GT

Hi John,

I will have to take a good look at the whole wireing harness front to back if it's all solid and intact $80.

Thanks

OK, $80 for the harness would be great.

If there are a few damaged wires or connectors I can fix it.

John

[quote name='porscheaddic' date='Oct 30 2008, 10:16 AM' post='1096566']
[quote name='msasnett' date='Oct 29 2008, 12:28 PM' post='1096260']
If the left rear fender is in good condition, I'm interested. Thanks!
[n

Hi,

Left rear fender is in nice shape no dents or rust $80 as much cut needed.

Thanks
[/quote]


I'm ready to buy this fender -- look for an email message with the details...

Thanks,

Mike

addic,

Can you sawzall the following for me & what is price & shipping to 85050?

It needs to include the center-section out past the ends of the fillets where they're tangent to the firewall. You don't have to go below the seam at the engine shelf - just up-to and including it.




THanks,

Hi Addic, Can I buy that left rear fender (quarter panel)?

Mike 650 793 2244

Does this car have turbo tie rods? If so, I'll buy em.

Bill

Lots of parts available.

front bumber pad, driver side door stay, passenger side rear quarter/sail (I have bad rust spot at just blow the sail almost to the door), rear brake calipers in order of priority. Shipping to Wisconsin.
9202844900

Are the rotors still available? If so shipping to 84648?

I need the 4 floor seat hinge pieces with the spot welded on brackets. If ya get to cutting the floor up.

Any console parts?????? If so zip is 43567 let me know what you have

anything? Need brackets Dave

Looking for a good condition front truck lid and passenger front/rear quarter panel. Let me know how yours are.

hello got a battery tray in good condition? Thanks, Joe

Hi

I am in need of the rear trunk panel. The one for my 914-6 race car has been messed with. I don't often visit this site. Can you please advise on availability, price, and shipping to New Port Richey, FL 34654.

Thanks and regards, Ken Greenfield rittmeister@earthlink.net

I would like the engine lid tabs cut off the body so I can weld them on my car to mount the engine lid. Also the rear license plate lights cut with the wires as long as possible.