maddog
Feb 11 2009, 07:14 AM
Click to view attachment914-6 BULKHEAD MOTOR MOUNT
This mount works on early or late cars, has access for the wiring loom and is designed to set the mount height to accommodate carbs, MFI, CIS or DME without major modification of the bulkhead piece. I have been selling this mount for over 10 years, this is the latest revision of the mount with all the changes suggested by customers who have bought this in the past. This mount is bolted to the firewall to determine location of engine and then is welded on for reinforcement. The welding will take about 10-15 minutes for someone that knows what they are doing and can be preformed after the engine is installed. None of the stock 914 equipment needs to be relocated. The mount also uses 911 motor mounts and standard mounting hardware. This mount is great for the do-it-yourself type person who is doing a six conversion and wants to save a little money. These mounts go for $500 + at a retailer. I accept Visa/MC through PayPal. FREE Shipping in the cont. US otherwise shipping on buyer, will ship internationally but buyer responsible for all shipping fees. Email me with any questions. Kit is $250.00 I also offer the hardware kit you will need to install this $85.00
sixaddict
Feb 11 2009, 09:06 AM
This is a great price. I am going to make a suggestion on your design though...I have this in a car and removed it to repaint (obviously bolted in) but the way the wiring harness was mounted it was fairly difficult to pull through the hole. I subsequently have have the triangular cut out near the center squared off so it has adequate room to slide the harness and grommet through. I feel that would be a positive modification.
TOT
maddog
Feb 13 2009, 09:08 AM
Tthanks for the input, I am allways open for feedback to make a better product. I think you have an older version, I have recently made a bunch of improvements to the mount. Instead of a hole for the wiring harness there is now a channel to go over the harness instead of pulling it through.
sixaddict
Feb 13 2009, 09:57 AM
I believe you are correct and I noticed the channel AFTER I sent the note. I'm just another hip shooter !
TOT
Rotary'14
Feb 14 2009, 07:55 PM
Hey Maddog,, I sent ya some pms. What's the paypal address that we gotta send the $$ to?
-Rob
maddog
Mar 17 2009, 09:55 AM
still have some mounts available $265 shipped in cont US.
RUNNINGWOLF
Mar 17 2009, 11:33 PM
QUOTE(maddog @ Mar 17 2009, 08:55 AM)
still have some mounts available $220 shipped in cont US.
Do you have any pictures of these installed?
If you are doing a six conversion, is this kit a requirement?
Thanks for the patience, in advance.
Runningwolf
PanelBilly
Mar 19 2009, 10:31 AM
I sent you an email too.
SLITS
Mar 19 2009, 11:54 AM
My installation in a 1970.This is one of his earlier mounts. Required some modification for the wiring harness on the early car. Also, had to be trimmed to get the installation height correct. Another inconvience I ran into was you could not install the front piece of 914/6 tin until the motor was in the chassis.
There are a couple of methods to install a six. This and the RJ Mount are the best as far as I am concerned.
CMAC
Apr 8 2009, 09:04 PM
Dave
I would like to go ahead and purchase the 914-6 bulkhead motor mount and hardware package. $300 including shipping.
Chuck
maddog
Apr 22 2009, 06:26 AM
Still have mounts available for $265 shipped and installation kits for $85, also ask about the 914-6 rear boxed arm stiffener kit and the 10 piece chassis stiffening kit available.
maddog
Jun 8 2009, 07:14 AM
bulkhead mounts and stiffeners still available.
maddog
Jul 27 2009, 08:05 AM
bump
maddog
Aug 11 2009, 12:55 PM
bump
maddog
Aug 26 2009, 06:22 AM
bump
maddog
Sep 9 2009, 06:39 AM
bulkhead motor mounts for your 6 conversion are still available for $265 shipped in the cont. US
maddog
Nov 18 2009, 06:27 AM
bulkhead motor mounts for your 6 conversion are now available for $265
Mark Henry
Nov 18 2009, 10:24 AM
What's the price shipped to Canada?
Thanks
maddog
Dec 4 2009, 06:40 AM
bump! check out my website for other parts that I sell for the 914
www.maddogsmotorsports.com
maddog
Dec 28 2009, 11:40 AM
bump
maddog
Jan 18 2010, 06:49 AM
have a couple of these Bulkhead motor mount kit $265 shipped if you are in the cont. US will ship internationally but contact first for a shipping quote
maddog
Aug 20 2012, 07:45 AM
if you buy multiple kits I can discount a little thanks for looking let me know if you have any questions.
dian
Oct 24 2012, 11:28 AM
hi
question on the 10 pc stiffening kit for 130$. where does it go and what does it do?
thanks.
maddog
May 12 2014, 07:10 PM
Bulkhead mounts kits and hardware kits are in stock and ready to ship
maddog
Mar 12 2018, 05:55 AM
bump! mounts are $250 check out my website for other parts that I sell for the 914
maddog
Jun 7 2019, 09:21 AM
stop by my website www.maddogsmotorsports.com for some great deals
This is a "lo-fi" version of our main content. To view the full version with more information, formatting and images, please
click here.