kyracedog
May 9 2009, 11:46 AM
Clearing out garage, parts from 74 that was converted to V8 track car.
1.7l engine case, crank, rods, heads, misc parts from long block $130
Old style Renegade SBC adapter plate, old flywheel, pressure plate for SBC $100
Combo gage $20 SOLD
Tach $20
Ignition switch w/key $50
Light switch $10 SOLD
Emergency flasher switch $10
Turn signal/wiper switch assy $50
Seat mounts $25/pr
Seat belts $10 pr SOLD
Center console with center seat pad $65 SOLD
Rear valance with dual exhaust cut outs, needs work $10
Dash top and knee pad, for recovering, $25 SOLD
Washer bottle $5 SOLD
Blower motor, controls, $20
Gage panel, painted $5 SOLD
Front fiberglass GT flares, $60/pr SOLD
Front struts, w/ rotors drilled for 5 lug, no studs, $50/pr ROTORS SOLD, STRUTS STILL AVAILABLE
Left and right side mirrors, vg cond $60/pr SOLD
Chrome trim for sail panels, $25/pr upright only SOLD
Old 19mm master cylinder, core $10
Back pad, good cond. $45 SOLD
Door panels, cloth, with pockets $50/pr SOLD
New short shift kit for early 911/912 w/901 trans $40 SOLD
All in good, used condition
Buyer pays shipping from Louisville KY, cashiers check, money order, or paypal only.
Pictures available, email ky911sc@insightbb.com for pics. Or PM from site
kyracedog
May 9 2009, 03:37 PM
QUOTE(hot_shoe914 @ May 9 2009, 11:36 AM)
What do you want a picture of?
bdstone914
May 9 2009, 10:14 PM
QUOTE(kyracedog @ May 9 2009, 01:37 PM)
QUOTE(hot_shoe914 @ May 9 2009, 11:36 AM)
What do you want a picture of?
I would like to the the center console. Is it the box and pad or the whole console?
Bruce
kyracedog
May 10 2009, 11:42 AM
QUOTE(bdstone914 @ May 9 2009, 08:14 PM)
QUOTE(kyracedog @ May 9 2009, 01:37 PM)
QUOTE(hot_shoe914 @ May 9 2009, 11:36 AM)
What do you want a picture of?
I would like to the the center console. Is it the box and pad or the whole console?
Bruce
Here are a couple of pictures, console and pad...hopefully you can see them..
Dan
rbmorrisiii
May 11 2009, 05:13 PM
Can I see a picture of the back pad and door panels, please.
RiveTech
May 11 2009, 05:20 PM
What condition are the seat belts in? My inertia reels are hanging up - I need to pull the seat belts out at a snail's pace to get them to release.
kyracedog
May 12 2009, 09:50 AM
QUOTE(rbmorrisiii @ May 11 2009, 03:13 PM)
Can I see a picture of the back pad and door panels, please.
kyracedog
May 12 2009, 09:51 AM
QUOTE(RiveTech @ May 11 2009, 03:20 PM)
What condition are the seat belts in? My inertia reels are hanging up - I need to pull the seat belts out at a snail's pace to get them to release.
I believe they worked ok.
bobhasissues
May 12 2009, 03:23 PM
QUOTE(kyracedog @ May 9 2009, 09:46 AM)
Clearing out garage, parts from 74 that was converted to V8 track car.
Chrome trim for sail panels, $25/pr upright only
All in good, used condition
Buyer pays shipping from Louisville KY, cashiers check, money order, or paypal only.
Pictures available, email ky911sc@insightbb.com for pics. Or PM from site
Dibs on sail panel trim, can you PM me some photos.
Thanks,
Bob
charliew
May 14 2009, 01:30 PM
Is the center console for a ac car and if it is is it good with no holes or loose seams?
kyracedog
May 14 2009, 07:01 PM
QUOTE(charliew @ May 14 2009, 11:30 AM)
Is the center console for a ac car and if it is is it good with no holes or loose seams?
Non A/C car as far as I know. No loose seams or holes in vinyl. I assume it is stock, never looked at another?
kyracedog
May 23 2009, 06:46 AM
Lots of stuff still left, I need the garage space...somebody needs these parts.
lotus_65
May 30 2009, 06:17 AM
what kind of work does the rear valance need? can you post a pic?
thanks
paul
kyracedog
May 30 2009, 07:15 PM
picture of rear valance as requested.
SLKWrx
Jun 2 2009, 09:19 AM
Any chance there is a working thermostat mixed in with the engine stuff? I could use one if you have it available.
Thanks
-- Steve
kyracedog
Jun 9 2009, 04:26 PM
QUOTE(SLKWrx @ Jun 2 2009, 07:19 AM)
Any chance there is a working thermostat mixed in with the engine stuff? I could use one if you have it available.
Thanks
-- Steve
NOt sure, will dig through the box to see if there is one, not sure if working thought.
kyracedog
Jun 9 2009, 04:27 PM
Still some stuff left, needs to go to someone who needs it..
make an offer on the remainder of the parts.
jd74914
Jun 9 2009, 05:05 PM
Could you post a pic of the turn signal/wiper assembly?
kyracedog
Jun 10 2009, 03:40 PM
Click to view attachmentQUOTE(jd74914 @ Jun 9 2009, 03:05 PM)
Could you post a pic of the turn signal/wiper assembly?
warrenoliver
Jun 17 2009, 08:52 PM
Do you still have the ignition switch Do you know if it still works?
Warrenoliver
RiqueMar
Jun 18 2009, 01:09 AM
Do you have a proportioning valve?