![]() |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
![]() ![]() |
![]() |
echocanyons |
![]()
Post
#1
|
Advanced Member ![]() ![]() ![]() ![]() Group: Benefactors Posts: 2,094 Joined: 24-December 02 From: Bay Area, CA Member No.: 7 Region Association: Central California ![]() ![]() ![]() |
I need to remove the axel flange from the transmission to replace them with 911 type.
Is there a tool? |
Red-Beard |
![]()
Post
#2
|
"Ya canna change the laws of Physics" ![]() ![]() ![]() Group: Benefactors Posts: 1,124 Joined: 11-February 03 From: Houston, TX Member No.: 288 Region Association: None ![]() ![]() |
Use a screwdriver through one of the CV bolt hole push it through to the case web so that the flange can't rotate.
I am pretty sure it's a 19mm. If not, it's 17mm. |
echocanyons |
![]()
Post
#3
|
Advanced Member ![]() ![]() ![]() ![]() Group: Benefactors Posts: 2,094 Joined: 24-December 02 From: Bay Area, CA Member No.: 7 Region Association: Central California ![]() ![]() ![]() |
Thanks!
Ill give it a shot |
echocanyons |
![]()
Post
#4
|
Advanced Member ![]() ![]() ![]() ![]() Group: Benefactors Posts: 2,094 Joined: 24-December 02 From: Bay Area, CA Member No.: 7 Region Association: Central California ![]() ![]() ![]() |
What are the torque specs for the 19mm bolt on reassemble?
|
Red-Beard |
![]()
Post
#5
|
"Ya canna change the laws of Physics" ![]() ![]() ![]() Group: Benefactors Posts: 1,124 Joined: 11-February 03 From: Houston, TX Member No.: 288 Region Association: None ![]() ![]() |
I'll have to look it up, but it's something like 75 or 85 ft-lbs.
James |
Gint |
![]()
Post
#6
|
Mike Ginter ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Group: Admin Posts: 16,083 Joined: 26-December 02 From: Denver CO. Member No.: 20 Region Association: Rocky Mountains ![]() ![]() |
I pulled output flanges on a prior 914. It's a piece of cake really. I don't recall the torque spec off the top of my head though.
|
echocanyons |
![]()
Post
#7
|
Advanced Member ![]() ![]() ![]() ![]() Group: Benefactors Posts: 2,094 Joined: 24-December 02 From: Bay Area, CA Member No.: 7 Region Association: Central California ![]() ![]() ![]() |
I didnt know they were bolted on until James pointed it out.
I had to look at them again to see the bolt set back in there. |
Red-Beard |
![]()
Post
#8
|
"Ya canna change the laws of Physics" ![]() ![]() ![]() Group: Benefactors Posts: 1,124 Joined: 11-February 03 From: Houston, TX Member No.: 288 Region Association: None ![]() ![]() |
A lot of times the bolt head is covered in CV grease.
|
Gint |
![]()
Post
#9
|
Mike Ginter ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Group: Admin Posts: 16,083 Joined: 26-December 02 From: Denver CO. Member No.: 20 Region Association: Rocky Mountains ![]() ![]() |
QUOTE I didnt know they were bolted on until James pointed it out. I had to look at them again to see the bolt set back in there. Ahh...crud in the works. Gotcha. I didn't mean anything by my comment. In retrospect I should have just said I agree with Red-Beard. |
echocanyons |
![]()
Post
#10
|
Advanced Member ![]() ![]() ![]() ![]() Group: Benefactors Posts: 2,094 Joined: 24-December 02 From: Bay Area, CA Member No.: 7 Region Association: Central California ![]() ![]() ![]() |
No offense taken the first time
|
echocanyons |
![]()
Post
#11
|
Advanced Member ![]() ![]() ![]() ![]() Group: Benefactors Posts: 2,094 Joined: 24-December 02 From: Bay Area, CA Member No.: 7 Region Association: Central California ![]() ![]() ![]() |
Hmmm, maybe I was thinking of 915 trans.
Do I need the 911 type flange to adapt to 911 cv's? Will the 914 type bolt up to the 911 cv's/axles? |
JWest |
![]()
Post
#12
|
Senior Member ![]() ![]() ![]() Group: Members Posts: 1,662 Joined: 6-January 03 From: Fort Worth, TX Member No.: 97 Region Association: None ![]() ![]() |
QUOTE(echocanyons @ Mar 21 2004, 11:40 PM) Hmmm, maybe I was thinking of 915 trans. Do I need the 911 type flange to adapt to 911 cv's? Will the 914 type bolt up to the 911 cv's/axles? If you are running 108mm 911 CVs, then you can use transmission flanges from a '69 to '71 911. |
echocanyons |
![]()
Post
#13
|
Advanced Member ![]() ![]() ![]() ![]() Group: Benefactors Posts: 2,094 Joined: 24-December 02 From: Bay Area, CA Member No.: 7 Region Association: Central California ![]() ![]() ![]() |
yup the stock flanges definitely will not work with the early( 69-71 ) 911 cv's
heres a pic the little one is the 914 part Attached image(s) ![]() |
ChrisFoley |
![]()
Post
#14
|
I am Tangerine Racing ![]() ![]() ![]() ![]() ![]() Group: Members Posts: 7,937 Joined: 29-January 03 From: Bolton, CT Member No.: 209 Region Association: None ![]() ![]() |
QUOTE(Red-Beard @ Mar 21 2004, 09:11 PM) I'll have to look it up, but it's something like 75 or 85 ft-lbs. James That much torque will surely snap the bolts. Try again. |
Red-Beard |
![]()
Post
#15
|
"Ya canna change the laws of Physics" ![]() ![]() ![]() Group: Benefactors Posts: 1,124 Joined: 11-February 03 From: Houston, TX Member No.: 288 Region Association: None ![]() ![]() |
Yup - 25-30 ft-lbs...
|
![]() ![]() |
![]() |
Lo-Fi Version | Time is now: 16th June 2024 - 07:09 PM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |