Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

2 Pages V  1 2 >  
 Reply to this topicStart new topic
> bearing inspection, how do these look?
Cool914
post Nov 21 2011, 11:14 AM
Post #1


Member
**

Group: Members
Posts: 98
Joined: 25-January 11
From: Ontario
Member No.: 12,627
Region Association: Canada
Taking apart a fresh rebuilt 2.0 and i noticed the heads qere on wrong side. The one with the head temp sensor spot was on 1,2cylinder side. possible reasons, problems?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
McMark
post Nov 21 2011, 11:16 AM
Post #2


914 Freak!
***************

Group: Retired Admin
Posts: 20,180
Joined: 13-March 03
From: Grand Rapids, MI
Member No.: 419
Region Association: None
Inattentive rebuilder. I did that on one of my first engines, you get excited to install the heads and forget which is which. Since both heads have bosses, I just drilled and tapped the other side and moved on.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Cool914
post Nov 21 2011, 12:09 PM
Post #3


Member
**

Group: Members
Posts: 98
Joined: 25-January 11
From: Ontario
Member No.: 12,627
Region Association: Canada
QUOTE(McMark @ Nov 21 2011, 09:16 AM) *

Inattentive rebuilder. I did that on one of my first engines, you get excited to install the heads and forget which is which. Since both heads have bosses, I just drilled and tapped the other side and moved on.

Thanks, good to know it is not problematic. i am going to pull the heads off to see what i have in there so i will just swap them back.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Cool914
post Nov 25 2011, 11:20 PM
Post #4


Member
**

Group: Members
Posts: 98
Joined: 25-January 11
From: Ontario
Member No.: 12,627
Region Association: Canada
So I started to take my "rebuilt" motor apart to see what I was dealing with. I am going to continue to split it while I am here and do 2056 with 9550 and my djet.
Here are the pictures of my 2.0 heads, looks like one intake valve and guide have been replaced. How do they look, anything stand out in terms of things to worry about? Is that seam on the inside of the intake part of the casting, seems to be in all the the intakes? There seems to be a few tiny pits around the top of the intake near the guide.

On a related note anyone know of good a machine shop in Canada to look over my GA case etc. as well as the heads?
Attached ImageAttached ImageAttached Image[attachmentid=284
413]Attached ImageAttached ImageAttached Image[attachmentid
=284405]Attached ImageAttached Image


Attached thumbnail(s)
Attached Image Attached Image Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Cool914
post Nov 25 2011, 11:28 PM
Post #5


Member
**

Group: Members
Posts: 98
Joined: 25-January 11
From: Ontario
Member No.: 12,627
Region Association: Canada
Last one of intake and some of cylinders. They look ok other than strange scratches. Pistons are marked with 93.97 and a X. Anyone know who made them?
Attached ImageAttached ImageAttached Image[attachmentid=284
414]


Attached thumbnail(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Mark Henry
post Nov 26 2011, 12:05 AM
Post #6


that's what I do!
***************

Group: Members
Posts: 20,065
Joined: 27-December 02
From: Port Hope, Ontario
Member No.: 26
Region Association: Canada
Looks like bus pistons. Heads don't look too bad
I can help with what you may need, PM me.

QUOTE
Is that seam on the inside of the intake part of the casting, seems to be in all the the intakes?

Normal casting marks.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
bam914
post Nov 26 2011, 09:30 AM
Post #7


Member
**

Group: Members
Posts: 342
Joined: 23-November 03
From: Atlanta, Ga
Member No.: 1,378
Region Association: None
I would have the valves replaced that one with all the pits in it looks bad.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
jmill
post Nov 26 2011, 09:42 AM
Post #8


Green Hornet
****

Group: Members
Posts: 2,449
Joined: 9-May 08
From: Racine, Wisconsin
Member No.: 9,038
Region Association: Upper MidWest
QUOTE(bam914 @ Nov 26 2011, 09:30 AM) *

I would have the valves replaced that one with all the pits in it looks bad.


(IMG:style_emoticons/default/agree.gif)



Attached thumbnail(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
jcd914
post Nov 26 2011, 11:06 AM
Post #9


Advanced Member
****

Group: Members
Posts: 2,096
Joined: 7-February 08
From: Sacramento, CA
Member No.: 8,684
Region Association: Northern California
QUOTE(Cool914 @ Posted Nov 21 2011, 09:14 AM) *

looks like one intake valve and guide have been replaced

This is a sure sign they were taking short cuts and only did the absolute bare minimum. Those heads should go to a machinist that knows 914 heads and be looked over. When does just 1 valve guide wear out and the others are all good?

Jim
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Jake Raby
post Nov 26 2011, 02:56 PM
Post #10


Engine Surgeon
*****

Group: Members
Posts: 9,398
Joined: 31-August 03
From: Lost
Member No.: 1,095
Region Association: South East States
Reusing valves is Russian Roulette.. Especially those that have seen damage from rust.
Tick. Tick.... wait for the boom!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
MrHyde
post Nov 26 2011, 03:50 PM
Post #11


Senior Member
***

Group: Members
Posts: 525
Joined: 13-October 10
From: Ontario, Canada
Member No.: 12,268
Region Association: None
QUOTE(Mark Henry @ Nov 26 2011, 01:05 AM) *

Looks like bus pistons. Heads don't look too bad
I can help with what you may need, PM me.




(IMG:style_emoticons/default/agree.gif)

Been to Marks a couple times now... If the pistons go sideways.. he probably has it..

Where in Ontario are you ?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Cool914
post Nov 26 2011, 07:03 PM
Post #12


Member
**

Group: Members
Posts: 98
Joined: 25-January 11
From: Ontario
Member No.: 12,627
Region Association: Canada
Thanks for the advice everyone. They will be getting all new valves and guides. Will work with Mark to get them sorted out. I am glad I decided to tear down the engine. I ordered Jake's video to help me figure out how to put it back together proper.

Hyde, I am in Ottawa.

Can't wait to see what is in the case, its like opening up a present, never know what your going to find. I found this sitting in the case, fell out of the bottom of the oil filler/breather piece.
Attached ImageAttached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Dave_Darling
post Nov 26 2011, 11:33 PM
Post #13


914 Idiot
***************

Group: Members
Posts: 15,209
Joined: 9-January 03
From: Silicon Valley / Kailua-Kona
Member No.: 121
Region Association: Northern California
Very common; that's the cover over the bottom of the PCV valve in the breather tower. It just plugs in, and seems to like to fall out after ~20 years when you remove the oil filler.

--DD
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
sean_v8_914
post Nov 27 2011, 09:33 AM
Post #14


Chingon 601
****

Group: Members
Posts: 4,011
Joined: 1-February 05
From: San Diego
Member No.: 3,541
post #12 is a tribute to Sir Andy
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Cool914
post Nov 28 2011, 06:02 PM
Post #15


Member
**

Group: Members
Posts: 98
Joined: 25-January 11
From: Ontario
Member No.: 12,627
Region Association: Canada
Do I need a new clutch disc?
Seriously though, do I need a new pressure plate, is it normal to have a little surface rust on there after sitting for awhile, will it just come off after some normal use, do I need to sand it off, or do I need to scrap it?
Attached ImageAttached ImageAttached Image[attachmentid=284
747]Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
a914dude
post Nov 28 2011, 06:16 PM
Post #16


Wanker
**

Group: Members
Posts: 247
Joined: 18-September 10
From: Saskatoon
Member No.: 12,191
Region Association: Rocky Mountains
Down to the rivits? Yes.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Mark Henry
post Nov 28 2011, 06:47 PM
Post #17


that's what I do!
***************

Group: Members
Posts: 20,065
Joined: 27-December 02
From: Port Hope, Ontario
Member No.: 26
Region Association: Canada
When you come down to see me bring it with you, I can check it and/or I have lots of engine spares.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Cool914
post Jan 2 2012, 08:49 PM
Post #18


Member
**

Group: Members
Posts: 98
Joined: 25-January 11
From: Ontario
Member No.: 12,627
Region Association: Canada
So I finally had time to finish the tear down. Didn't look that bad to me, but what do I know. I didnt find any chips or groves on the case bearing surfaces, but the one thing I did find is that the bearing numbers made an impression on the case surface on the centre main and from what I read in the Tom Wilson book is that means it was hammered in there and the bore will now be oval. Has anyone found that to be the case? I cant find anyone in town to align bore it so was hoping to remain STD. I will have the case measured at a local shop to check but they will have no type 4 knowledge. The crank looked perfect. Whats up with the elephant, that a VW symbol?
Attached ImageAttached ImageAttached Image[attachmentid=289
727]Attached ImageAttached ImageAttached Image[attachmentid
=289731]Attached ImageAttached Image


Attached thumbnail(s)
Attached Image Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Cool914
post Jan 2 2012, 08:56 PM
Post #19


Member
**

Group: Members
Posts: 98
Joined: 25-January 11
From: Ontario
Member No.: 12,627
Region Association: Canada
the rest
Attached ImageAttached ImageAttached Image[attachmentid=289
737]Attached ImageAttached ImageAttached Image[attachmentid
=289741]Attached Image


Attached thumbnail(s)
Attached Image Attached Image Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Cool914
post Jan 2 2012, 09:00 PM
Post #20


Member
**

Group: Members
Posts: 98
Joined: 25-January 11
From: Ontario
Member No.: 12,627
Region Association: Canada
Attached Image

sorry, here is a good one of the impression of the bearing numbers
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
« Next Oldest · 914World Garage · Next Newest »
 

2 Pages V  1 2 >
Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 

Display Mode: Standard · Switch to: Linear+ · Switch to: Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

- Lo-Fi Version Time is now: 31st July 2025 - 02:31 PM
Invision Power Board v9.1.4 © 2025  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...