Fuel line grommets, Can't find |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
Fuel line grommets, Can't find |
Cornerlot |
Jul 12 2016, 07:50 AM
Post
#1
|
Member Group: Members Posts: 89 Joined: 4-June 16 From: New Braunfels, TX Member No.: 20,070 Region Association: Southwest Region |
I'm new to 914's, previously I've just fooled with 911's.
I now have a '70 914-6 with the fuel tank out and need to replace the rubber grommets for the fuel lines. These are where the 2 fuel lines (different O.D.'s) enter the tunnel under the tank, both going through their own OVAL holes (one line per hole). Any ideas? The closest I found are the PN 111957861 oval grommets for the brake reservoir lines and fuel in the 914-4 engine bay. The PET shows both a NLA single large oval grommet in some cars set up for 2 lines, or a un-pictured NLA grommet PN 99970209550 for single lines. Steve |
napasteve |
Jul 12 2016, 08:34 AM
Post
#2
|
914 driving winemaker Group: Members Posts: 509 Joined: 2-January 13 From: Napa, CA Member No.: 15,327 Region Association: Northern California |
|
altitude411 |
Jul 12 2016, 08:57 AM
Post
#3
|
I drove my 6 into a tree Group: Members Posts: 1,306 Joined: 21-September 14 From: montana Member No.: 17,932 Region Association: Rocky Mountains |
Mark carries these 10 mm as well as 8 mm.
http://shop.914rubber.com/Fuel-line-grommet-10mm-10mmFLG.htm |
Rotary'14 |
Jul 12 2016, 10:03 AM
Post
#4
|
Senior Member Group: Members Posts: 753 Joined: 24-April 05 From: Los Angeles Member No.: 3,977 |
Hi,,
914-6 has front grommets similiar to the engine shelf grommets. I have those available at $4 each plus shipping. -Robert |
Mikey914 |
Jul 12 2016, 10:36 AM
Post
#5
|
The rubber man Group: Members Posts: 12,729 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None |
Yep, I have the rear ones. If you can't find what you need. I can probably make it. Just let me know.
Attached thumbnail(s) |
Cornerlot |
Jul 12 2016, 11:24 AM
Post
#6
|
Member Group: Members Posts: 89 Joined: 4-June 16 From: New Braunfels, TX Member No.: 20,070 Region Association: Southwest Region |
Yep, I have the rear ones. If you can't find what you need. I can probably make it. Just let me know. The round ones won't work, they are larger and oval. The engine shelf ones may work. Right now I have the stock lines, so angled 8mm and 10mm should work. Steve |
Cornerlot |
Jul 12 2016, 11:26 AM
Post
#7
|
Member Group: Members Posts: 89 Joined: 4-June 16 From: New Braunfels, TX Member No.: 20,070 Region Association: Southwest Region |
Your 914-6 setup is different than my 73 2.0 pictured below. I reused my single big grommet when installing SS lines; it was in good condition. You might contact Chris at Tangerine Racing. He may be able to help you. That 914-4 grommet is larger than my single line grommets. The dual line one is NLA any ways. Steve |
Cornerlot |
Jul 12 2016, 11:36 AM
Post
#8
|
Member Group: Members Posts: 89 Joined: 4-June 16 From: New Braunfels, TX Member No.: 20,070 Region Association: Southwest Region |
A picture before they fell apart ...
|
Dave_Darling |
Jul 12 2016, 05:06 PM
Post
#9
|
914 Idiot Group: Members Posts: 15,051 Joined: 9-January 03 From: Silicon Valley / Kailua-Kona Member No.: 121 Region Association: Northern California |
Those do look an awful lot like the engine shelf grommets.
--DD |
Mikey914 |
Jul 13 2016, 12:34 AM
Post
#10
|
The rubber man Group: Members Posts: 12,729 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None |
Well I have these, which I think you may be referring to. They are the larger ID
http://shop.914rubber.com/Vent-hose-bushin...99970204950.htm Attached image(s) |
Mikey914 |
Jul 13 2016, 12:38 AM
Post
#11
|
The rubber man Group: Members Posts: 12,729 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None |
Attached thumbnail(s) |
Cornerlot |
Jul 13 2016, 08:10 AM
Post
#12
|
Member Group: Members Posts: 89 Joined: 4-June 16 From: New Braunfels, TX Member No.: 20,070 Region Association: Southwest Region |
|
Mikey914 |
Jul 14 2016, 12:28 AM
Post
#13
|
The rubber man Group: Members Posts: 12,729 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None |
thanks Steve,
They are elliptical, the angle of the photo is distorting the perspective. Yes my photography sucks. |
Lo-Fi Version | Time is now: 31st October 2024 - 05:43 PM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |