 Front trunk seal, Not staying in place |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| dudzy's914 |
 Jul 5 2017, 10:11 AM
Post
#1
|
|
The youngin'  Group: Members Posts: 271 Joined: 21-December 13 From: Hatfield, MA Member No.: 16,784 Region Association: North East States  |
My front trunk seal will just not stay in place. How does it stay in?
Thanks, Finn |
   |
 
|
| Lucky9146 |
Jul 5 2017, 10:31 AM
Post
#2
|
|
Always Wanted A Bigger Go Cart Group: Members Posts: 1,676 Joined: 22-September 14 From: Poway California Member No.: 17,942 Region Association: Southern California 
|
I used this. 3 M Super Weatherstrip and Gasket Adhesive. Yellow. Commonly referred to as "snake snot" worked perfect on mine
Good luck  |
|
|
|
| PanelBilly |
Jul 5 2017, 10:46 AM
Post
#3
|
|
914 Guru Group: Members Posts: 5,883 Joined: 23-July 06 From: Kent, Wa Member No.: 6,488 Region Association: Pacific Northwest
|
I warmed mine up just a bit with a heatgun and then left the truck closed on it
|
|
|
|
| Mikey914 |
Jul 5 2017, 10:52 AM
Post
#4
|
|
The rubber man Group: Members Posts: 12,767 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None
|
Also make sure you have oriented correctly. It is possible install upside down. You can tell as the area at the cowl has a step down. It has been molded into the seal.
It will also make sure it shuts correctly and seals at the top. Mark |
|
|
|
| Tom_T |
Jul 5 2017, 11:46 AM
Post
#5
|
|
TMI.... Group: Members Posts: 8,321 Joined: 19-March 09 From: Orange, CA Member No.: 10,181 Region Association: Southern California
|
QUOTE(Lucky9146 @ Jul 5 2017, 09:31 AM)  I used this. 3 M Super Weatherstrip and Gasket Adhesive. Yellow. Commonly referred to as "snake snot" worked perfect on mine Good luck I think that there are black gasket adhesives out there which will do as good of a job & not scream YELLOW around the edges of your gasket. Permatex makes a good one which we used on our 88 Westy's pop-top seal, which has a lot of pulling forces when lifting the top up. And what mark/Mikey914 said - whether his 914Rubber repros or factory seals - the bottom is usually flat(-ish), & IIRC the 914 Factory Repair Manual says to run a small bead in the tray on the body [not on the seal bottom]. If not adhered, then the seals tend to pull apart at the 8 corners - especially the front corners ones around the headlight buckets. If yours tear/separate, then you can use that same Permatex gasket/seal adhesive to repair them with a dab inside the joint at the corners, then adhere in place in the tray. Good Luck! (IMG:style_emoticons/default/beerchug.gif) Tom /////// |
|
|
|
| Lucky9146 |
Jul 5 2017, 01:02 PM
Post
#6
|
|
Always Wanted A Bigger Go Cart Group: Members Posts: 1,676 Joined: 22-September 14 From: Poway California Member No.: 17,942 Region Association: Southern California
|
QUOTE(Lucky9146 @ Jul 5 2017, 09:31 AM) I used this. 3 M Super Weatherstrip and Gasket Adhesive. Yellow. Commonly referred to as "snake snot" worked perfect on mine Good luck Further to my earlier post. You should not see any adhesive as you only place it in the very bottom of the channel the gasket sits it. Be careful not to get it all over the place when applying in the channel and you may want to mask off while applying. I do not know about the black suggested above but I do know this adhesive works well and I have used it with good results over the years. Let us know how it turns our for you what ever you use. |
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 13th May 2025 - 01:18 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.