914-6 GT oil breather set up, mini project DIY thread |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
914-6 GT oil breather set up, mini project DIY thread |
Retroracer |
Jun 7 2019, 06:31 PM
Post
#1
|
Senior Member Group: Members Posts: 616 Joined: 7-July 13 From: Bend OR Member No.: 16,100 Region Association: Pacific Northwest |
So my GT tribute is on the road, but in my rush to get behind the wheel (and to get the project off axle stands!), one or two items were "delayed until later". One of the these was to figure out a GT style oil breather/catch tank solution.
Looking through the excellent PBASE photo stash of all things 914-6 GT (thx Mr Serrano!), the oil breather seems to be one of those areas in which the various factory cars differed a little from each other. An old 911 washer bottle seemed to be the preferred receptacle (but not always); The Sonauto cars seemed to place it on the trunk bulkhead, while the Monte and Nurburgring cars favored the LHS rear trunk placement: After looking at the options, I decided to go for a mounting similar to the Nurburgring cars, which meant two key items would be needed: - an early 911 washer bottle - a bracket made up to imitate the factory mount So I scored a copy of an early 911 washer bottle via eBay from a vendor in Seattle. I cannot condone the pricing on these items, but where else are you going to get one? Original ones look like hell and still go for over $100. There is a Mercedes VDO one which has similar dimensions but has subtle differences to the Porsche version. And it's still $90. Anyway, I grumbled a bit and then ordered one. So having obtained the receptacle, now a bracket would be needed: Looking closely at the pictures and scaling to the washer bottle, I figured out some 1" strip could be bent up to suit. The factory ones looked to be of steel (?), and spot welded at the end to a vertical to attach it to the frame. I decided - mostly as I don't have access to a spot welder - to make up one in aluminum and epoxy it together (I don't see this structure having to withstand heavy lateral loading). I happened to have some aluminum bar in my stash, so got right to forming it. I used a 1" diameter former to do the corner bends, to roughly match the contours of the washer bottle, and the material was soft enough to be able to hand formed (no hammers needed): The tab at the end was then drilled on the outside so that when clamped and epoxied, the goop would partially fill the holes, so after painting it would resemble the factory spot weld: |
Retroracer |
Jun 7 2019, 06:47 PM
Post
#2
|
Senior Member Group: Members Posts: 616 Joined: 7-July 13 From: Bend OR Member No.: 16,100 Region Association: Pacific Northwest |
The vertical was then made from the same material, drilled out as well (this would be on the other side, so would mirror the spot weld effect on the front). Much offering up and checking of angles was needed, as the vertical is - well, not quite vertical - and it angles away to match the frame contours.
Once happy with the fit, this was clamped and epoxied to the lozenge-shaped bracket: A second, mostly hidden bracket was made up to give some support to the front. This bracket needed a 'jog' in it to line up vertically: The main bracket was then attached to the frame at the vertical using self-tapping, stainless steel countersunk crews (note that that the frame is double skinned here, so the threads do not protrude into the wheel arches). Then the second bracket was epoxied and clamped in place to make sure everything sat together ok: Once cured, then its all ready for paint prep: |
Retroracer |
Jun 7 2019, 07:00 PM
Post
#3
|
Senior Member Group: Members Posts: 616 Joined: 7-July 13 From: Bend OR Member No.: 16,100 Region Association: Pacific Northwest |
Then just a case of prep:
semi-gloss black painting and final install: Then just a case of connecting a 5/8" PVC clear hose through to the engine bay, sizing the pipe and adapting that to the breather pipe on the side of the 914-6 oil filler neck (which needed an intermediate 10AN pipe step down, from the 1" dia outlet): ...and job done. Next project: mount the Cibie iode 45's additional driving lights to the outside front. I see more brackets in my future.... - Tony |
crsedge |
Jun 7 2019, 11:02 PM
Post
#4
|
Newbie Group: Members Posts: 32 Joined: 25-March 12 From: Australia Member No.: 14,304 Region Association: None |
Well done!!
|
rgalla9146 |
Jun 8 2019, 05:29 AM
Post
#5
|
Advanced Member Group: Members Posts: 4,569 Joined: 23-November 05 From: Paramus NJ Member No.: 5,176 Region Association: None |
Excellent work.
|
mb911 |
Jun 8 2019, 05:33 AM
Post
#6
|
914 Guru Group: Members Posts: 6,883 Joined: 2-January 09 From: Burlington wi Member No.: 9,892 Region Association: Upper MidWest |
Do you have a link for the eBay part?
|
Retroracer |
Jun 8 2019, 07:22 AM
Post
#7
|
Senior Member Group: Members Posts: 616 Joined: 7-July 13 From: Bend OR Member No.: 16,100 Region Association: Pacific Northwest |
Do you have a link for the eBay part? this won't age well but: https://www.ebay.com/itm/Porsche-New-SWB-91...VkAAOSwUu5b9xrh - Tony |
tygaboy |
Jun 8 2019, 07:37 AM
Post
#8
|
914 Guru Group: Members Posts: 5,314 Joined: 6-October 15 From: Petaluma, CA Member No.: 19,241 Region Association: Northern California |
And with countersunk fasteners... Very tidy all around. Nicely done! (IMG:style_emoticons/default/first.gif)
|
mb911 |
Jun 12 2019, 02:40 PM
Post
#9
|
914 Guru Group: Members Posts: 6,883 Joined: 2-January 09 From: Burlington wi Member No.: 9,892 Region Association: Upper MidWest |
Well reluctant to but did it anyway ordered one today.. Guess I will do the same thing it only seems right.
|
Lo-Fi Version | Time is now: 9th June 2024 - 08:40 PM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |