 After Market Blinker switch experience?, Does your switch cancel on its own? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| Steve |
 Jun 15 2020, 07:39 AM
Post
#1
|
|
914 Guru  Group: Members Posts: 5,606 Joined: 14-June 03 From: Orange County, CA Member No.: 822 Region Association: Southern California 
 |
My horn was going on and off on its own, so I bought a blinker switch to fix the problem.
I bought a blinker switch from Sierra Madre and one from Jbuggs. Both came in the same white box. Both fixed the horn problem and everything else works, but when you turn a corner, the blinker does not cancel on its own. Same steering wheel and horn ring which worked fine on the previous switch. I also noticed the cancel do hickey, does not stick out as far as the original one. Any recommendations for one that does cancel on its own? (IMG:style_emoticons/default/huh.gif) (IMG:style_emoticons/default/blink.gif) (IMG:style_emoticons/default/wacko.gif) |
   |
 
|
| 76-914 |
Jun 15 2020, 08:05 AM
Post
#2
|
|
Repeat Offender & Resident Subaru Antagonist Group: Members Posts: 13,507 Joined: 23-January 09 From: Temecula, CA Member No.: 9,964 Region Association: Southern California
|
|
 |
|
| dr914@autoatlanta.com |
Jun 15 2020, 08:55 AM
Post
#3
|
|
914 Guru Group: Members Posts: 7,887 Joined: 3-January 07 From: atlanta georgia Member No.: 7,418 Region Association: None |
important that when you connect the turn signal switch to the wiper switch that both insert into the column very easily with no pressure and that the screws go all of th eway in not pulling the assembly down. If they are used to pull the assembly in then the switch will bind and the stalk not return
QUOTE(Steve @ Jun 15 2020, 06:39 AM)  My horn was going on and off on its own, so I bought a blinker switch to fix the problem. I bought a blinker switch from Sierra Madre and one from Jbuggs. Both came in the same white box. Both fixed the horn problem and everything else works, but when you turn a corner, the blinker does not cancel on its own. Same steering wheel and horn ring which worked fine on the previous switch. I also noticed the cancel do hickey, does not stick out as far as the original one. Any recommendations for one that does cancel on its own? (IMG:style_emoticons/default/huh.gif) (IMG:style_emoticons/default/blink.gif) (IMG:style_emoticons/default/wacko.gif) |
|
|
|
| Steve |
Jun 15 2020, 10:46 AM
Post
#4
|
|
914 Guru Group: Members Posts: 5,606 Joined: 14-June 03 From: Orange County, CA Member No.: 822 Region Association: Southern California
|
Thanks Doc!! Next time I pull the wheel, I will check it out again.
|
|
|
|
| ClayPerrine |
Jun 15 2020, 11:47 AM
Post
#5
|
|
Life's been good to me so far..... Group: Admin Posts: 15,502 Joined: 11-September 03 From: Hurst, TX. Member No.: 1,143 Region Association: NineFourteenerVille
|
The last aftermarket switch I bought canceled just fine. But it would let out a loud SCREECH when turning the steering wheel.
I was ORDERED to put the old one back by the owner. (IMG:style_emoticons/default/driving-girl.gif) (IMG:style_emoticons/default/betty914.jpg) |
|
|
|
| TheCabinetmaker |
Jun 16 2020, 06:58 AM
Post
#6
|
|
I drive my car everyday Group: Members Posts: 8,301 Joined: 8-May 03 From: Tulsa, Ok. Member No.: 666 |
Lmao, Clay!
|
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st June 2024 - 11:13 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.