 Quick release hubs |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| BillJ |
 Jan 28 2023, 11:01 AM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,275 Joined: 4-March 13 From: charlotte, NC Member No.: 15,610 Region Association: None 
 |
What are the racers using these days for quick release hubs? I have a setup with a dual pull pin setup but sometimes it binds and i want to refresh it. I have an original 6 so a different steering column and spline so want to see specifically for theat equipment.
Looking for excellent no fail designs where cost isnt the biggest factor. |
   |
 
|
| sixnotfour |
Jan 29 2023, 06:28 PM
Post
#2
|
|
914 Wizard Group: Members Posts: 10,824 Joined: 12-September 04 From: Life Elevated..planet UT. Member No.: 2,744 Region Association: Rocky Mountains 
|
Rothsport Racing. makes one based on the Porsche one they used... https://rothsport.com/collections/quick-rel...ering-hub-clear
|
|
|
|
| BillJ |
Jan 29 2023, 07:52 PM
Post
#3
|
|
Senior Member Group: Members Posts: 1,275 Joined: 4-March 13 From: charlotte, NC Member No.: 15,610 Region Association: None
|
Will check it out!
|
|
|
|
| BillJ |
Feb 18 2023, 04:24 PM
Post
#4
|
|
Senior Member Group: Members Posts: 1,275 Joined: 4-March 13 From: charlotte, NC Member No.: 15,610 Region Association: None
|
Ok so i found what i needed. Rennline makes a very short hub converter. Have it in hand and all is well. Just got.the old one off and have a question.
Should the steering shaft have any play? I am getting a good amount of deflection something like 1/2 inch if i had to guess. Is thhere a bushing i should insert before putting this back together? |
|
|
|
| BillJ |
Feb 18 2023, 04:40 PM
Post
#5
|
|
Senior Member Group: Members Posts: 1,275 Joined: 4-March 13 From: charlotte, NC Member No.: 15,610 Region Association: None
|
Nevermind. Once the hub adapter went in the flange pressed into the bushing and it is now snug.
Attached thumbnail(s)  
|
|
|
|
| sixnotfour |
Feb 19 2023, 02:10 PM
Post
#6
|
|
914 Wizard Group: Members Posts: 10,824 Joined: 12-September 04 From: Life Elevated..planet UT. Member No.: 2,744 Region Association: Rocky Mountains
|
|
|
|
|
| Huck271 |
Feb 19 2023, 05:09 PM
Post
#7
|
|
Newbie Group: Members Posts: 3 Joined: 19-February 23 From: The Woodlands, TX Member No.: 27,172 Region Association: Southwest Region |
QUOTE(BillJ @ Feb 18 2023, 04:40 PM)  Nevermind. Once the hub adapter went in the flange pressed into the bushing and it is now snug. Is your steering wheel centered over the driver seat? |
|
|
|
| BillJ |
Feb 19 2023, 11:22 PM
Post
#8
|
|
Senior Member Group: Members Posts: 1,275 Joined: 4-March 13 From: charlotte, NC Member No.: 15,610 Region Association: None
|
Using the stock location and rails so no the wheel sits a couple inches to the riight.
|
|
|
|
|
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 11th May 2025 - 05:43 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.