 Wiper motor wiring connections - Please help, Need help with wiper motor wiring |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| Bret_Jet |
 Oct 27 2005, 05:31 PM
Post
#1
|
|
Newbie  Group: Members Posts: 3 Joined: 27-October 05 From: Oregon Member No.: 5,012  |
Hello - I lost my wiring diagram for the wiper motor in my '75 914 2.0. I installed the wiper assembly and I have 4 spade connectors on the back of the motor, looking at the assembly from the front of the car - 1 horizontal at the top, 1 vertical to the right, left and bottom, and 1 spade connector off to the right by itself, which looks like probably a ground. There are 5 wires with connectors BLU/BLK, BRN (2 brown wires into one connector), BLK, RED/WHT+RED/BLK (2 wires going into one connector), and GRN/WHT.
Please can anyone help by telling me the position as per my description that these wires should be connected? I have the wiring diagram in the Haynes book which is really of no help, at least for me, as it doesn't show which wires go to which connectors. There are no numbers next to the spade connectors. TIA! |
   |
 
|
| grasshopper |
Oct 27 2005, 08:14 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 2,613 Joined: 10-December 04 From: Valdosta, GA Member No.: 3,258 Region Association: None |
the two browns go on the connector off to the side..... I just reinstalled mine today, but it's late, and i dont feel like going back out to the garage, so ill get the rest tomorrow.... LaTeR
|
|
|
|
| Bret_Jet |
Oct 28 2005, 01:53 AM
Post
#3
|
|
Newbie Group: Members Posts: 3 Joined: 27-October 05 From: Oregon Member No.: 5,012 |
Ahh, Grasshopper - you are a life saver! Thanks. I'll look for your post tomorrow - can't tell you how much I appreciate it as I can't proceed to install the rest of the junk until I connect those wires!
|
|
|
|
| grasshopper |
Oct 28 2005, 09:51 AM
Post
#4
|
|
Advanced Member Group: Members Posts: 2,613 Joined: 10-December 04 From: Valdosta, GA Member No.: 3,258 Region Association: None |
ok, Black and blue goes to the top connector, the green and white goes to the connector on the left, the black one goes on the bottom, and the red/white + red/black wires go to the connector on the right. Hope the helps with your project, i'm reinstalling my harness now too, so if you need anything else just email or PM me.
|
|
|
|
| jim_hoyland |
Oct 28 2005, 11:01 AM
Post
#5
|
|
Get that VIN ? Group: Members Posts: 9,815 Joined: 1-May 03 From: Sunset Beach, CA Member No.: 643 Region Association: Southern California 
|
Do you have an intermittant wiper relay ?
|
|
|
|
| grasshopper |
Oct 28 2005, 11:10 AM
Post
#6
|
|
Advanced Member Group: Members Posts: 2,613 Joined: 10-December 04 From: Valdosta, GA Member No.: 3,258 Region Association: None |
are you asking me if i have one, or are you asking him, trying to give him help??
|
|
|
|
| Bret_Jet |
Oct 28 2005, 12:09 PM
Post
#7
|
|
Newbie Group: Members Posts: 3 Joined: 27-October 05 From: Oregon Member No.: 5,012 |
Awesome Barry - thanks again.
Not sure about intermittent wiper - the car has been apart for several years now and just now getting around to putting all back together. But the wire colors that Grasshopper has and mine are the same so I am going to go with those connections. Thanks for the help! |
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 12th July 2025 - 04:50 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.