 h.e headache, can they be put i backwards |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| nycchef |
 Oct 10 2008, 04:50 PM
Post
#1
|
|
mechanical moron  Group: Members Posts: 952 Joined: 28-November 05 From: new york city n.y. Member No.: 5,202 Region Association: None  |
well not actually backwards, but on the wrong side. i reinsalled the h.e on the passenger side and in went in without a hitch, now the driver side wont line up with the studs. could i have put them on the wrong side/ does anyone have a good pic of a completey installed system for a 2.0? with all the tubes and hoses. i am trully lost (IMG:style_emoticons/default/sad.gif)
|
   |
 
|
| r_towle |
Oct 10 2008, 04:53 PM
Post
#2
|
|
Custom Member Group: Members Posts: 24,705 Joined: 9-January 03 From: Taxachusetts Member No.: 124 Region Association: North East States 
|
The HE goes outside the motor...so when the tubes turn they move the HE towards the outside of the car...
Rich |
|
|
|
| nycchef |
Oct 10 2008, 05:16 PM
Post
#3
|
|
mechanical moron Group: Members Posts: 952 Joined: 28-November 05 From: new york city n.y. Member No.: 5,202 Region Association: None |
QUOTE(r_towle @ Oct 10 2008, 02:53 PM)  The HE goes outside the motor...so when the tubes turn they move the HE towards the outside of the car... Rich so how do you tell the left from the right? |
|
|
|
| r_towle |
Oct 10 2008, 05:21 PM
Post
#4
|
|
Custom Member Group: Members Posts: 24,705 Joined: 9-January 03 From: Taxachusetts Member No.: 124 Region Association: North East States
|
Well if you put it on so it pointed the way I described it would aim the exchanger forward.
Look at the pipes that go to the head. About 3 inches from the head, both pipes bend 90 degrees. That would move the HE towards the outside of the car when properly installed. If you somehow (not even sure if it possible) managed to install it the wrong way, that 90 degree bend would move the HE towards the middle of the car. If the HE is no lining up with the head stud, check to make sure the head studs are straight and then make sure the HE little U tabs for the studs are straight and clean on the inside. Sometimes you may need to take a file and ream out the u tabs on the HE to get it to work. RIch |
|
|
|
| r_towle |
Oct 10 2008, 05:22 PM
Post
#5
|
|
Custom Member Group: Members Posts: 24,705 Joined: 9-January 03 From: Taxachusetts Member No.: 124 Region Association: North East States
|
here is a pic.
Attached thumbnail(s) 
|
|
|
|
| r_towle |
Oct 10 2008, 05:23 PM
Post
#6
|
|
Custom Member Group: Members Posts: 24,705 Joined: 9-January 03 From: Taxachusetts Member No.: 124 Region Association: North East States
|
Forget looking at the muffler in this picture.
Look at the HE;s From the back of the car these HE's in the pic above are on the correct side. See the bend in the front pipes> Rich |
|
|
|
| nycchef |
Oct 10 2008, 05:31 PM
Post
#7
|
|
mechanical moron Group: Members Posts: 952 Joined: 28-November 05 From: new york city n.y. Member No.: 5,202 Region Association: None |
QUOTE(r_towle @ Oct 10 2008, 03:23 PM) Forget looking at the muffler in this picture. Look at the HE;s From the back of the car these HE's in the pic above are on the correct side. See the bend in the front pipes> Rich thanks rich i'm just losing it. i got them on the right side just have to check if a stud is bent |
|
|
|
| nycchef |
Oct 10 2008, 08:21 PM
Post
#8
|
|
mechanical moron Group: Members Posts: 952 Joined: 28-November 05 From: new york city n.y. Member No.: 5,202 Region Association: None |
still need to figure out the j-tube/flapper box/etc layout. if anyone has a diagram or pic i could use to see it
thanks |
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 10:22 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.