Pressing on Rear Droplinks |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
Pressing on Rear Droplinks |
Trav012000 |
Apr 24 2009, 02:41 PM
Post
#1
|
Member Group: Members Posts: 59 Joined: 23-September 08 From: Indiana, USA Member No.: 9,583 Region Association: Upper MidWest |
Okay so it took me awhile but I finally got my rear droplink bushings pressed into the droplinks. Now I'm trying to get the droplinks attached to the car. Does anyone have a magical way of making this happen? '76 model year if it matters. (IMG:style_emoticons/default/smile.gif)
Thanks guys. |
Cupomeat |
Apr 24 2009, 02:52 PM
Post
#2
|
missing my NY 914 in VA Group: Members Posts: 1,336 Joined: 26-November 07 From: Oakton VA Member No.: 8,376 Region Association: MidAtlantic Region |
Hmmm, I think I had the exact same questions but I can't find the thread.
The answer appears to be the largest channel locks you can find, or a wooden drift and a big hammer. Hope that helps. |
Trav012000 |
Apr 24 2009, 02:57 PM
Post
#3
|
Member Group: Members Posts: 59 Joined: 23-September 08 From: Indiana, USA Member No.: 9,583 Region Association: Upper MidWest |
Hmmm, I think I had the exact same questions but I can't find the thread. The answer appears to be the largest channel locks you can find, or a wooden drift and a big hammer. Hope that helps. Apparently I didnt try my channel locks quite hard enough. (IMG:style_emoticons/default/biggrin.gif) |
Tom |
Apr 24 2009, 04:38 PM
Post
#4
|
Advanced Member Group: Members Posts: 2,139 Joined: 21-August 05 From: Port Orchard, WA 98367 Member No.: 4,626 Region Association: None |
When I did mine, I used a large C-clamp. Worked well, just had to keep it aligned or it wanted to slip off. Lubed them up also.
Tom |
r_towle |
Apr 24 2009, 05:39 PM
Post
#5
|
Custom Member Group: Members Posts: 24,585 Joined: 9-January 03 From: Taxachusetts Member No.: 124 Region Association: North East States |
BFH...I use a rubber one.
A very well placed very powerful hit will do it. Rich |
SLITS |
Apr 24 2009, 07:55 PM
Post
#6
|
"This Utah shit is HARSH!" Group: Benefactors Posts: 13,602 Joined: 22-February 04 From: SoCal Mountains ... Member No.: 1,696 Region Association: None |
Big channel locks
|
Dave_Darling |
Apr 24 2009, 09:53 PM
Post
#7
|
914 Idiot Group: Members Posts: 14,991 Joined: 9-January 03 From: Silicon Valley / Kailua-Kona Member No.: 121 Region Association: Northern California |
A "squeeze to tighten" bar clamp. Use a jack to move one trailing arm or the other upward to get the ball on the arm lined up with the socket in the drop-link.
I've also used a C-clamp, but it was hard to keep lined up correctly while tightening the clamp. --DD |
ConeDodger |
Apr 24 2009, 11:43 PM
Post
#8
|
Apex killer! Group: Members Posts: 23,605 Joined: 31-December 04 From: Tahoe Area Member No.: 3,380 Region Association: Northern California |
I have heard that drilling a small hole threw the back of the bushing lets the air out and makes it easier so you are not compressing air too...
|
dgw |
Apr 25 2009, 10:37 AM
Post
#9
|
Dennis Winter Group: Members Posts: 553 Joined: 7-January 03 From: Santa Cruz Mountains Member No.: 106 Region Association: Northern California |
A "squeeze to tighten" bar clamp. Use a jack to move one trailing arm or the other upward to get the ball on the arm lined up with the socket in the drop-link. I've also used a C-clamp, but it was hard to keep lined up correctly while tightening the clamp. --DD the bar clamp worked well for me also. I could not make it work with a C clamp, hammer, etc. |
Joe Ricard |
Apr 25 2009, 11:42 AM
Post
#10
|
CUMONIWANNARACEU Group: Members Posts: 6,811 Joined: 5-January 03 From: Gautier, MS Member No.: 92 |
Channel locks on the sway bar side
Hammer on the control arm side |
rascobo |
Apr 25 2009, 07:38 PM
Post
#11
|
Member Group: Members Posts: 203 Joined: 26-July 07 From: Portland,OR. Member No.: 7,948 Region Association: Pacific Northwest |
I have heard that drilling a small hole threw the back of the bushing lets the air out and makes it easier so you are not compressing air too... (IMG:style_emoticons/default/agree.gif) It's how I've been doing mine for years. It makes them much easier to get on, and haven't found any drawbacks. |
SirAndy |
Apr 25 2009, 11:04 PM
Post
#12
|
Resident German Group: Admin Posts: 41,669 Joined: 21-January 03 From: Oakland, Kalifornia Member No.: 179 Region Association: Northern California |
When I did mine, I used a large C-clamp. Worked well, just had to keep it aligned or it wanted to slip off. (IMG:style_emoticons/default/agree.gif) |
charliew |
Apr 26 2009, 09:22 PM
Post
#13
|
Advanced Member Group: Members Posts: 2,363 Joined: 31-July 07 From: Crawford, TX. Member No.: 7,958 |
Seems like adding a hole would help but it also would make it easier for crud to migrate through the bushing.
|
Trav012000 |
Apr 27 2009, 07:27 AM
Post
#14
|
Member Group: Members Posts: 59 Joined: 23-September 08 From: Indiana, USA Member No.: 9,583 Region Association: Upper MidWest |
Channel Locks worked guys thanks. Clamps would have been better. And I thought about drilling a hole. Would have helped too, I apparently squeezed so hard 3 of my fingers ended up bleeding from the cuticle. (IMG:style_emoticons/default/smile.gif)
|
Lo-Fi Version | Time is now: 31st May 2024 - 10:37 PM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |