 Heater control cables |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| PanelBilly |
 Jul 2 2009, 08:08 PM
Post
#1
|
|
914 Guru  Group: Members Posts: 5,881 Joined: 23-July 06 From: Kent, Wa Member No.: 6,488 Region Association: Pacific Northwest 
 |
 After attempting to get everything adjusted right on while in place, I decided to pull it out and hook it up on the floor. That way I could tweek each cable adjustment so the flaps all worked togeather and the controls opened and closed when they were in the full right and full left position. After marking the wires on the control boxes I can take it apart and reinstall it in the car in the same spot. Anybody who's pulled these units all the way apart should reassemble on the bench first. |
   |
 
|
| geniusanthony |
Jul 3 2009, 12:15 AM
Post
#2
|
|
Its a brand new "Chrome-sicle" Group: Members Posts: 517 Joined: 12-December 05 From: Alexandria,VA Member No.: 5,266 Region Association: MidAtlantic Region |
Are you making sure to mark where the cables are clamped down before you dissassemble? That way everything should go back together as you intend. Great project by the way.
|
|
|
|
| Gint |
Jul 3 2009, 08:48 AM
Post
#3
|
|
Mike Ginter Group: Admin Posts: 16,096 Joined: 26-December 02 From: Denver CO. Member No.: 20 Region Association: Rocky Mountains  |
I have a set I pulled from a 72 that I left connected and intact. Let me know if you need pics or something.
|
|
|
|
| RiqueMar |
Jul 3 2009, 10:13 AM
Post
#4
|
|
Enrique Allen Mar Group: Members Posts: 2,243 Joined: 28-August 08 From: San Diego, CA Member No.: 9,478 Region Association: Southern California
|
QUOTE(Gint @ Jul 3 2009, 07:48 AM)  I have a set I pulled from a 72 that I left connected and intact. Let me know if you need pics or something. Hey Gint, I'm at about the same place too, mind posting that pic? |
|
|
|
| PanelBilly |
Jul 3 2009, 10:25 AM
Post
#5
|
|
914 Guru Group: Members Posts: 5,881 Joined: 23-July 06 From: Kent, Wa Member No.: 6,488 Region Association: Pacific Northwest
|
I put masking tape on the cable sheild and on the wires to mark them. Disconnected the control panel from the assembly and then installed it again in the car. Worked great.
|
|
|
|
| Gint |
Jul 3 2009, 12:25 PM
Post
#6
|
|
Mike Ginter Group: Admin Posts: 16,096 Joined: 26-December 02 From: Denver CO. Member No.: 20 Region Association: Rocky Mountains |
QUOTE(RiqueMar @ Jul 3 2009, 09:13 AM) QUOTE(Gint @ Jul 3 2009, 07:48 AM) I have a set I pulled from a 72 that I left connected and intact. Let me know if you need pics or something. Hey Gint, I'm at about the same place too, mind posting that pic?Sure. I have some other odds and ends to get done today before it gets hot. I'll get it in a couple-3 hours. |
|
|
|
| Gint |
Jul 3 2009, 05:07 PM
Post
#7
|
|
Mike Ginter Group: Admin Posts: 16,096 Joined: 26-December 02 From: Denver CO. Member No.: 20 Region Association: Rocky Mountains |
Not the best pics.
        |
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 03:27 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.