 Is the front suspension crossmember the same for all years? What's a fair price? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| doug_b_928 |
 Aug 3 2014, 08:24 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 692 Joined: 17-January 13 From: Winnipeg Member No.: 15,382 Region Association: Canada  |
As the topic title suggests, I'm wondering if the front suspension crossmember is the same for all years. I did a search and saw a few older posts indicating that $25-$30 is the going rate. Is that a reasonable/fair price?
|
   |
 
|
  |
Replies(1 - 8)
| bdstone914 |
Aug 3 2014, 08:33 PM
Post
#2
|
|
bdstone914 Group: Members Posts: 4,536 Joined: 8-November 03 From: Riverside CA Member No.: 1,319 |
QUOTE(doug_b_928 @ Aug 3 2014, 07:24 PM)  As the topic title suggests, I'm wondering if the front suspension crossmember is the same for all years. I did a search and saw a few older posts indicating that $25-$30 is the going rate. Is that a reasonable/fair price? They are the same for all years and there is little call for them. I have only sold them if they were blasted and powder coated. If anyone will pay $25 I would take it. Bruce |
 |
|
| larryM |
Aug 3 2014, 09:06 PM
Post
#3
|
|
emoze Group: Members Posts: 891 Joined: 1-January 03 From: mid- California Member No.: 65 Region Association: Northern California 
|
I gave one away last year - complete - with all suspension parts attached & hubs & rotors -
|
|
|
|
| doug_b_928 |
Aug 4 2014, 07:27 AM
Post
#4
|
|
Senior Member Group: Members Posts: 692 Joined: 17-January 13 From: Winnipeg Member No.: 15,382 Region Association: Canada |
I would happily pay for a good one, but the shipping from CA to Canada might be too expensive. If either of you have one to sell, please check shipping to Winnipeg. If that ends up being too much, we can also try shipping to Pembina, ND and I can drive down there (1 hour each way) and pick it up.
|
|
|
|
| rhodyguy |
Aug 4 2014, 08:00 AM
Post
#5
|
|
Chimp Sanctuary NW. Check it out. Group: Members Posts: 22,090 Joined: 2-March 03 From: Orion's Bell. The BELL! Member No.: 378 Region Association: Galt's Gulch |
i would think it would cost $40ish, maybe more, with the customs hassles, to winnipeg. USPS would be easier than fedex. what's your time worth + fuel?
k |
|
|
|
| stugray |
Aug 4 2014, 12:34 PM
Post
#6
|
|
Advanced Member Group: Members Posts: 3,825 Joined: 17-September 09 From: Longmont, CO Member No.: 10,819 Region Association: None |
While on this topic: Are we talking about the piece that can be replaced by a 911 aluminum version?
What are the years/models of 911 to look for for that substitution? |
|
|
|
| doug_b_928 |
Aug 4 2014, 01:26 PM
Post
#7
|
|
Senior Member Group: Members Posts: 692 Joined: 17-January 13 From: Winnipeg Member No.: 15,382 Region Association: Canada |
QUOTE(rhodyguy @ Aug 4 2014, 09:00 AM) i would think it would cost $40ish, maybe more, with the customs hassles, to winnipeg. USPS would be easier than fedex. what's your time worth + fuel? k I may head down to Pembina to pick something up anyway, so if it was sent early this week then I could get it at the same time. |
|
|
|
| bdstone914 |
Aug 4 2014, 09:11 PM
Post
#8
|
|
bdstone914 Group: Members Posts: 4,536 Joined: 8-November 03 From: Riverside CA Member No.: 1,319 |
QUOTE(stugray @ Aug 4 2014, 11:34 AM) While on this topic: Are we talking about the piece that can be replaced by a 911 aluminum version? What are the years/models of 911 to look for for that substitution? .74 and later 911. |
|
|
|
| doug_b_928 |
Aug 5 2014, 08:58 AM
Post
#9
|
|
Senior Member Group: Members Posts: 692 Joined: 17-January 13 From: Winnipeg Member No.: 15,382 Region Association: Canada |
Does anyone have a straight one of these to sell?
|
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 8th June 2024 - 04:20 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.