 XL Front Sway bat Mounts, Bigger, badder version |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Engman |
 Feb 26 2005, 09:43 PM
Post
#1
|
|
Zoisite  Group: Benefactors Posts: 1,349 Joined: 25-March 03 From: New Albany, IN Member No.: 475   |
Please see http://engmanparts.com for details. Set of 2 - will work with up to a 31mm sway bar.
PM or email me..... M Attached thumbnail(s) 
|
   |
 
|
  |
Replies(1 - 7)
| Jeroen |
Feb 27 2005, 07:22 AM
Post
#2
|
|
914 Guru Group: Members Posts: 7,887 Joined: 24-December 02 From: The Netherlands Member No.: 3 Region Association: Europe |
Can you explain a little?
I can see there's more meat to the plate it self, but what about the extra holes? |
|
|
|
| Engman |
Feb 27 2005, 01:58 PM
Post
#3
|
|
Zoisite Group: Benefactors Posts: 1,349 Joined: 25-March 03 From: New Albany, IN Member No.: 475 |
The 3 holes are to be puddle welded to the car, then weld the edges all around. This plate is almost 50 percent larger than the old ones - you will have to notch out more area to fit it in.
M |
|
|
|
| Andyrew |
Jan 30 2006, 05:24 PM
Post
#4
|
|
Spooling.... Please wait Group: Members Posts: 13,378 Joined: 20-January 03 From: Riverbank, Ca Member No.: 172 Region Association: Northern California 
|
Whats the ID of the hole?
|
|
|
|
| Engman |
Jan 30 2006, 06:42 PM
Post
#5
|
|
Zoisite Group: Benefactors Posts: 1,349 Joined: 25-March 03 From: New Albany, IN Member No.: 475 |
You can go up to a 31mm sway bar - largest I know of.
M |
|
|
|
| Andyrew |
Jan 31 2006, 03:11 AM
Post
#6
|
|
Spooling.... Please wait Group: Members Posts: 13,378 Joined: 20-January 03 From: Riverbank, Ca Member No.: 172 Region Association: Northern California
|
Whats the ID in inches?
I have a 1 1/4in sway bar.. (IMG:http://www.914world.com/bbs2/html/emoticons/biggrin.gif) |
|
|
|
| Engman |
Jan 31 2006, 12:26 PM
Post
#7
|
|
Zoisite Group: Benefactors Posts: 1,349 Joined: 25-March 03 From: New Albany, IN Member No.: 475 |
These are sized at 1.24" currently - I *can* open up a set to 1.31" if you are interested.
On a side note - what bar are you planning on running? M |
|
|
|
| Andyrew |
Jan 31 2006, 02:47 PM
Post
#8
|
|
Spooling.... Please wait Group: Members Posts: 13,378 Joined: 20-January 03 From: Riverbank, Ca Member No.: 172 Region Association: Northern California
|
Nascar bar, 1 1/4 in 49 spline turned down to 3/4 inch. should provide between 70-200lbs of stiffness (or more) and i'll make the arms adjustable.
Bar I got from Brett (thanks!!) Bushing or bearing is my only problem. but I have a couple ideas on that. Andrew |
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 04:35 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.