 More mystery tins |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Amphicar770 |
 May 8 2016, 11:37 AM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,198 Joined: 20-April 10 From: PA, USA Member No.: 11,639 Region Association: MidAtlantic Region 
 |
Hi all,
Heat exchangers and related vita back on my '74 2.0. I have two tins that look like they would go in the heat exchanger area. Not sure if they're off my car or from the extra set of tins I had off of a 75-76. If they do go on my car can't figure out which side is which or which side is up. I should have done more jigsaw puzzles as a child. Any insight appreciated. Thx. Mike  |
   |
 
|
  |
Replies(1 - 8)
| rhodyguy |
May 8 2016, 11:54 AM
Post
#2
|
|
Chimp Sanctuary NW. Check it out. Group: Members Posts: 22,098 Joined: 2-March 03 From: Orion's Bell. The BELL! Member No.: 378 Region Association: Galt's Gulch |
The one on the right is the driver's side warm air guide. The curve is in the top when mounted. Other is for the pass side. They only attach one way. The 2 cutouts are reliefs for the h.e. pipes. You'll see when you get under the car.
|
|
|
|
| Amphicar770 |
May 8 2016, 12:13 PM
Post
#3
|
|
Senior Member Group: Members Posts: 1,198 Joined: 20-April 10 From: PA, USA Member No.: 11,639 Region Association: MidAtlantic Region
|
QUOTE(rhodyguy @ May 8 2016, 01:54 PM)  The one on the right is the driver's side warm air guide. The curve is in the top when mounted. Other is for the pass side. They only attach one way. The 2 cutouts are reliefs for the h.e. pipes. You'll see when you get under the car. Thanks. I'm under car now and still perplexed. (IMG:style_emoticons/default/confused24.gif) Let's focus on drivers side 1st. Does this sit between exchanger and engine or below exchanger? When you say the curve, you mean the long straight bit that looks like is would cover a pipe? Hump is facing up? Sorry for th confusion. Hard to picture 3D in text and I'm probably missing something obvious?.. |
|
|
|
| SA-914 |
May 8 2016, 12:21 PM
Post
#4
|
|
Member Group: Members Posts: 128 Joined: 30-June 14 From: San Antonio,tx Member No.: 17,566 Region Association: Southwest Region |
This is what I have.
Attached thumbnail(s) 
|
|
|
|
| SA-914 |
May 8 2016, 12:23 PM
Post
#5
|
|
Member Group: Members Posts: 128 Joined: 30-June 14 From: San Antonio,tx Member No.: 17,566 Region Association: Southwest Region |
The hump forms the channel for the shift rod. The tin will end up above the rod
|
|
|
|
| SA-914 |
May 8 2016, 12:25 PM
Post
#6
|
|
Member Group: Members Posts: 128 Joined: 30-June 14 From: San Antonio,tx Member No.: 17,566 Region Association: Southwest Region |
Passenger side.
Attached thumbnail(s) 
|
|
|
|
| Amphicar770 |
May 8 2016, 12:27 PM
Post
#7
|
|
Senior Member Group: Members Posts: 1,198 Joined: 20-April 10 From: PA, USA Member No.: 11,639 Region Association: MidAtlantic Region
|
Ok, got it. The AA descrip that it sits between block and exchanger threw me off.
Here is photo for future noobs like me.   |
|
|
|
| SA-914 |
May 8 2016, 12:56 PM
Post
#8
|
|
Member Group: Members Posts: 128 Joined: 30-June 14 From: San Antonio,tx Member No.: 17,566 Region Association: Southwest Region |
Did the PO install my green taco plate upside down?
|
|
|
|
| SLITS |
May 8 2016, 05:17 PM
Post
#9
|
|
"This Utah shit is HARSH!" Group: Benefactors Posts: 13,602 Joined: 22-February 04 From: SoCal Mountains ... Member No.: 1,696 Region Association: None  |
QUOTE(SA-914 @ May 8 2016, 11:56 AM) Did the PO install my green taco plate upside down? No, you just don't have the cover piece. |
|
|
|
|
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 17th June 2024 - 02:05 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.