Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

> Gaskets, Valve cover
cpavlenko
post Sep 14 2016, 05:47 PM
Post #1


Member
**

Group: Members
Posts: 489
Joined: 19-April 12
From: North Arizona
Member No.: 14,400
Region Association: Southwest Region



what type gaskets for 1971 1.7, I've heard there tricky to get them in right. Also what type of gasket sealer is recommended?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
2 Pages V  1 2 >  
Reply to this topicStart new topic
Replies(1 - 19)
jcd914
post Sep 14 2016, 06:15 PM
Post #2


Advanced Member
****

Group: Members
Posts: 2,096
Joined: 7-February 08
From: Sacramento, CA
Member No.: 8,684
Region Association: Northern California



I have always used gasgacinch to stick the cork gasket to the valve cover.
After the gasgacinch dries, I smear a thin coating of swepco 101 moly grease on the head side of the gasket. Then the gasket does not stick to the head and the cover can be shifted around to make sure it is seated. I often reused the old gaskets several times this way.

Jim
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
914Sixer
post Sep 14 2016, 06:24 PM
Post #3


914 Guru
*****

Group: Members
Posts: 9,181
Joined: 17-January 05
From: San Angelo Texas
Member No.: 3,457
Region Association: Southwest Region



Get some of 914Rubber high temp reusable gaskets and be done.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cpavlenko
post Sep 14 2016, 06:43 PM
Post #4


Member
**

Group: Members
Posts: 489
Joined: 19-April 12
From: North Arizona
Member No.: 14,400
Region Association: Southwest Region



QUOTE(914Sixer @ Sep 14 2016, 05:24 PM) *

Get some of 914Rubber high temp reusable gaskets and be done.

what do u use to hold them in place on the valve cover?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Mikey914
post Sep 14 2016, 07:54 PM
Post #5


The rubber man
**********

Group: Members
Posts: 12,772
Joined: 27-December 04
From: Hillsboro, OR
Member No.: 3,348
Region Association: None



The cork are cheap and stick well. If you use the silicone, cleaned and decrease, if you want a small amount of silicone to glue in place.
Mark
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cpavlenko
post Sep 14 2016, 08:11 PM
Post #6


Member
**

Group: Members
Posts: 489
Joined: 19-April 12
From: North Arizona
Member No.: 14,400
Region Association: Southwest Region



QUOTE(Mikey914 @ Sep 14 2016, 06:54 PM) *

The cork are cheap and stick well. If you use the silicone, cleaned and decrease, if you want a small amount of silicone to glue in place.
Mark

Thanks for the info.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
euro911
post Sep 14 2016, 08:40 PM
Post #7


Retired & living the dream. God help me if I wake up!
*****

Group: Members
Posts: 8,911
Joined: 2-December 06
From: So.Cal. & No.AZ (USA)
Member No.: 7,300
Region Association: Southern California



I recommend the thicker cork gaskets that Mark (914 Rubber) makes.

I just smear a bit of hi-temp grease on both sides of the gaskets. The grease helps to keep them in place, as well as keeping oil from seeping through.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cpavlenko
post Sep 14 2016, 09:03 PM
Post #8


Member
**

Group: Members
Posts: 489
Joined: 19-April 12
From: North Arizona
Member No.: 14,400
Region Association: Southwest Region



QUOTE(euro911 @ Sep 14 2016, 07:40 PM) *

I recommend the thicker cork gaskets that Mark (914 Rubber) makes.

I just smear a bit of hi-temp grease on both sides of the gaskets. The grease helps to keep them in place, as well as keeping oil from seeping through.

Hi Mark, hows things going at Payson. Thanks for the info. One day I'll take a trip to your neck of the woods. PM me your phone# and address. I'm still learning a lot on the 914. I now know how to adjust the valves correctly. Live and learn the hard way, but it wasn't as hard as I thought it would be. Just a PITA for a 62 yr old guy under that teener. Hope to here from you.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
euro911
post Sep 14 2016, 09:18 PM
Post #9


Retired & living the dream. God help me if I wake up!
*****

Group: Members
Posts: 8,911
Joined: 2-December 06
From: So.Cal. & No.AZ (USA)
Member No.: 7,300
Region Association: Southern California



QUOTE(cpavlenko @ Sep 14 2016, 08:03 PM) *
QUOTE(euro911 @ Sep 14 2016, 07:40 PM) *
I recommend the thicker cork gaskets that Mark (914 Rubber) makes.

I just smear a bit of hi-temp grease on both sides of the gaskets. The grease helps to keep them in place, as well as keeping oil from seeping through.
Hi Mark, hows things going at Payson. Thanks for the info. One day I'll take a trip to your neck of the woods. PM me your phone# and address. I'm still learning a lot on the 914. I now know how to adjust the valves correctly. Live and learn the hard way, but it wasn't as hard as I thought it would be. Just a PITA for a 62 yr old guy under that teener. Hope to here from you.
I know the feeling (62 myself) ... but look at the bright side - Elliot is older (IMG:style_emoticons/default/poke.gif)

Having a lift is a real plus for working on these cars, even one of the smaller mid-rise lifts. In fact, a mid-rise is also great for changing tires, doing brakes & suspension work (IMG:style_emoticons/default/cool_shades.gif) (I'll have to buy another 4-post for tha AZ home - sold mine to my old shop's landlord).

I'm in CA right now, have a good-sized list of 'honey-doos' to complete. I'm continually adding to the list of stuff I need to take to AZ + staging it right now. I also have to source a new control board for my furnace before going back ... I think it's gonna be late fall or winter by then (IMG:style_emoticons/default/dry.gif)

I'll PM you the pertinent info and let you know when I plan to be in AZ again.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cpavlenko
post Sep 14 2016, 09:24 PM
Post #10


Member
**

Group: Members
Posts: 489
Joined: 19-April 12
From: North Arizona
Member No.: 14,400
Region Association: Southwest Region



QUOTE(euro911 @ Sep 14 2016, 08:18 PM) *

QUOTE(cpavlenko @ Sep 14 2016, 08:03 PM) *
QUOTE(euro911 @ Sep 14 2016, 07:40 PM) *
I recommend the thicker cork gaskets that Mark (914 Rubber) makes.

I just smear a bit of hi-temp grease on both sides of the gaskets. The grease helps to keep them in place, as well as keeping oil from seeping through.
Hi Mark, hows things going at Payson. Thanks for the info. One day I'll take a trip to your neck of the woods. PM me your phone# and address. I'm still learning a lot on the 914. I now know how to adjust the valves correctly. Live and learn the hard way, but it wasn't as hard as I thought it would be. Just a PITA for a 62 yr old guy under that teener. Hope to here from you.
I know the feeling (62 myself) ... but look at the bright side - Elliot is older (IMG:style_emoticons/default/poke.gif)

Having a lift is a real plus for working on these cars, even one of the smaller mid-rise lifts. In fact, a mid-rise is also great for changing tires, doing brakes & suspension work (IMG:style_emoticons/default/cool_shades.gif) (I'll have to buy another 4-post for tha AZ home - sold mine to my old shop's landlord).

I'm in CA right now, have a good-sized list of 'honey-doos' to complete. I'm continually adding to the list of stuff I need to take to AZ + staging it right now. I also have to source a new control board for my furnace before going back ... I think it's gonna be late fall or winter by then (IMG:style_emoticons/default/dry.gif)

I'll PM you the pertinent info and let you know when I plan to be in AZ again.

Sounds good, if u need any help, let me know. Take care.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
JawjaPorsche
post Sep 15 2016, 02:37 AM
Post #11


Advanced Member
****

Group: Members
Posts: 3,463
Joined: 23-July 11
From: Clayton, Georgia
Member No.: 13,351
Region Association: South East States



QUOTE(euro911 @ Sep 14 2016, 10:40 PM) *

I recommend the thicker cork gaskets that Mark (914 Rubber) makes.

I just smear a bit of hi-temp grease on both sides of the gaskets. The grease helps to keep them in place, as well as keeping oil from seeping through.


(IMG:style_emoticons/default/agree.gif)

I used to get small leaks until I started using 914Rubber's thicker gaskets! Problem solved!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Frankvw
post Sep 15 2016, 03:07 AM
Post #12


working on my first 914 !
***

Group: Members
Posts: 653
Joined: 13-April 16
From: Holland, the Netherlands
Member No.: 19,896
Region Association: Europe



I can speak from my experience in the VW world (Type1, but also Type4 engines) that I never used any adhesive, sealant or anything like that when installing the cork valvecover gaskets.
When the snapped on coverholder does not have enough tension to keep the cover firm in its spot, it can leak and if the valve cover is warped same thing. If the valvecover is straight and there is enough pressure to hold the cover there should be no need for any product to add.
I know there is a difference in cork-gasket quality, the Original VW ones are really good, so maybe poor quality gaskets can change things to use....
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
VaccaRabite
post Sep 15 2016, 09:21 AM
Post #13


En Garde!
**********

Group: Admin
Posts: 13,752
Joined: 15-December 03
From: Dallastown, PA
Member No.: 1,435
Region Association: MidAtlantic Region



In my experience, if you use a LITTLE smear of RTV between the gasket and the valve cover, nothing is needed between the gasket and the head.

Also, the gaskets will last years this way without leaking, even after opening the covers up for regular valve adjustments.

Zach
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Mikey914
post Sep 15 2016, 10:34 AM
Post #14


The rubber man
**********

Group: Members
Posts: 12,772
Joined: 27-December 04
From: Hillsboro, OR
Member No.: 3,348
Region Association: None



QUOTE(Frankvw @ Sep 15 2016, 02:07 AM) *

I can speak from my experience in the VW world (Type1, but also Type4 engines) that I never used any adhesive, sealant or anything like that when installing the cork valvecover gaskets.
When the snapped on coverholder does not have enough tension to keep the cover firm in its spot, it can leak and if the valve cover is warped same thing. If the valvecover is straight and there is enough pressure to hold the cover there should be no need for any product to add.
I know there is a difference in cork-gasket quality, the Original VW ones are really good, so maybe poor quality gaskets can change things to use....

This could be the real issue. I know that there are other valve cover gaskets that sell at about what my raw material cost is for these. You can make stuff in China, but the material cost will not have much variation, unless you make it cheaper somehow??? It's the only way they could sell at the prices they do and have any margin.

Oh and by the way we did make our sealing surface slightly wider.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Elliot Cannon
post Sep 15 2016, 12:59 PM
Post #15


914 Guru
*****

Group: Retired Members
Posts: 8,487
Joined: 29-December 06
From: Paso Robles Ca. (Central coast)
Member No.: 7,407
Region Association: None



"Elliot is older". And smarter, better looking, faster driver, etc. etc. (IMG:style_emoticons/default/av-943.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Elliot Cannon
post Sep 15 2016, 01:04 PM
Post #16


914 Guru
*****

Group: Retired Members
Posts: 8,487
Joined: 29-December 06
From: Paso Robles Ca. (Central coast)
Member No.: 7,407
Region Association: None



Read this. http://www.pelicanparts.com/techarticles/9...alve_covers.htm
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
euro911
post Sep 15 2016, 02:17 PM
Post #17


Retired & living the dream. God help me if I wake up!
*****

Group: Members
Posts: 8,911
Joined: 2-December 06
From: So.Cal. & No.AZ (USA)
Member No.: 7,300
Region Association: Southern California



QUOTE(Elliot Cannon @ Sep 15 2016, 11:59 AM) *
"Elliot is older". And smarter, better looking, faster driver, etc. etc. (IMG:style_emoticons/default/av-943.gif)
Choo gottit, mang ... except for the 'faster driver' part (IMG:style_emoticons/default/laugh.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
rhodyguy
post Sep 15 2016, 02:40 PM
Post #18


Chimp Sanctuary NW. Check it out.
***************

Group: Members
Posts: 22,248
Joined: 2-March 03
From: Orion's Bell. The BELL!
Member No.: 378
Region Association: Galt's Gulch



I'd be hard pressed to hack up a set of 2.0 tin to provide those vent tubes. Or any set for that matter. Note the carb intake. The cinch-a-gasket works well on the stock cover side. Only! Install the cover with the VW symbol upside down, iirc.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cpavlenko
post Sep 15 2016, 03:21 PM
Post #19


Member
**

Group: Members
Posts: 489
Joined: 19-April 12
From: North Arizona
Member No.: 14,400
Region Association: Southwest Region



QUOTE(rhodyguy @ Sep 15 2016, 01:40 PM) *

I'd be hard pressed to hack up a set of 2.0 tin to provide those vent tubes. Or any set for that matter. Note the carb intake. The cinch-a-gasket works well on the stock cover side. Only! Install the cover with the VW symbol upside down, iirc.

Y upside down?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Elliot Cannon
post Sep 15 2016, 08:48 PM
Post #20


914 Guru
*****

Group: Retired Members
Posts: 8,487
Joined: 29-December 06
From: Paso Robles Ca. (Central coast)
Member No.: 7,407
Region Association: None



QUOTE(rhodyguy @ Sep 15 2016, 01:40 PM) *

I'd be hard pressed to hack up a set of 2.0 tin to provide those vent tubes. Or any set for that matter. Note the carb intake. The cinch-a-gasket works well on the stock cover side. Only! Install the cover with the VW symbol upside down, iirc.


Did you miss the point of the article? (IMG:style_emoticons/default/biggrin.gif) You know, valve cover gaskets?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post

2 Pages V  1 2 >
Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



- Lo-Fi Version Time is now: 2nd July 2025 - 01:19 PM