Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

> alternator suitability
JFG
post Jun 29 2017, 01:48 PM
Post #1


Senior Member
***

Group: Members
Posts: 686
Joined: 7-April 16
From: Wales
Member No.: 19,869
Region Association: None
The vw replacement alternator number is 021-903-023-A,
On the 914 parts catalog it is 022 903 023.

Looking at images online i see the vw has some kind of suppressor on it (causing shorts until remedied) the one on my engine (likely a 411) does not have this. It also has no numbers on it.

Does the 914 alternator have the suppressor? Can i fit the vw numbered alternator without issues?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
 
 Reply to this topicStart new topic
Replies(1 - 7)
Mikey914
post Jun 29 2017, 11:53 PM
Post #2


The rubber man
**********

Group: Members
Posts: 12,767
Joined: 27-December 04
From: Hillsboro, OR
Member No.: 3,348
Region Association: None
Good question (IMG:style_emoticons/default/popcorn[1].gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
JFG
post Jul 6 2017, 11:20 AM
Post #3


Senior Member
***

Group: Members
Posts: 686
Joined: 7-April 16
From: Wales
Member No.: 19,869
Region Association: None
For those as electronically challenged as myself I have an answer.

The alternator is fine. The suppressor which caused my confusion is part number 021 903 295 and is a separate part whereas I thought it was integral. Duh!

Anyhow back to making I'll fitting parts fit!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
mgphoto
post Jul 6 2017, 02:27 PM
Post #4


"If there is a mistake it will find me"
***

Group: Members
Posts: 1,375
Joined: 1-April 09
From: Los Angeles, CA
Member No.: 10,225
Region Association: Southern California
Problems arise with the positive lug, our type iv has a very short one to accommodate the air deflector plate, longer lug from a different unit can short on the plate. Also there is a gasket between the alternator and the air deflector plate, NLA gasket seals for better cooling, no electric isolation.
Mike
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
914Sixer
post Jul 6 2017, 07:33 PM
Post #5


914 Guru
*****

Group: Members
Posts: 9,123
Joined: 17-January 05
From: San Angelo Texas
Member No.: 3,457
Region Association: Southwest Region
Positive terminal (red wire) is supposed to have a rubber cap on it.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
JFG
post Jul 7 2017, 11:14 AM
Post #6


Senior Member
***

Group: Members
Posts: 686
Joined: 7-April 16
From: Wales
Member No.: 19,869
Region Association: None
You're both correct in what you say. The positive threads are longer and should have a boot. Only one b+ has the starter live wire connected so naturally only one boot (elbow) is found. I'm going to fab some kind of gasket / spacer and or reduce the length of the threaded studs.

I read a thread on the samba about this problem.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Mikey914
post Jul 7 2017, 11:43 AM
Post #7


The rubber man
**********

Group: Members
Posts: 12,767
Joined: 27-December 04
From: Hillsboro, OR
Member No.: 3,348
Region Association: None
We have made the replacement harness with the correct cap on it. Also working on the deflector, boot, and some other little goodies that fit in there. Unfortunately, they are several weeks out. But the harness is in stock if you need one. Do check to see if the 3 prong connector is brittle, and it the red wire has evidence of melting the protective covering.

http://shop.914rubber.com/Alternator-wirin...m?categoryId=-1

Here's a code for $15 off it you need one

"ALT10"
In fact one of those parts is also ready and on sale (I'll start a dedicated thread)

Hope this helps


Attached thumbnail(s)
Attached Image

Attached image(s)
Attached Image Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
jim_hoyland
post Jul 7 2017, 04:02 PM
Post #8


Get that VIN ?
*****

Group: Members
Posts: 9,696
Joined: 1-May 03
From: Sunset Beach, CA
Member No.: 643
Region Association: Southern California
QUOTE(Mikey914 @ Jul 7 2017, 10:43 AM) *

We have made the replacement harness with the correct cap on it. Also working on the deflector, boot, and some other little goodies that fit in there. Unfortunately, they are several weeks out. But the harness is in stock if you need one. Do check to see if the 3 prong connector is brittle, and it the red wire has evidence of melting the protective covering.



Are you going to make the gasket too ? (IMG:style_emoticons/default/smile.gif) (The one that goes under the backing plate )
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
« Next Oldest · 914World Garage · Next Newest »
 

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 

Display Mode: Switch to: Standard · Linear+ · Switch to: Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

- Lo-Fi Version Time is now: 9th May 2025 - 04:31 PM
Invision Power Board v9.1.4 © 2025  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...