 Headlight Actuactor Arm, How is it held on? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| BeatNavy |
 May 13 2020, 03:14 PM
Post
#1
|
|
Certified Professional Scapegoat  Group: Members Posts: 2,951 Joined: 26-February 14 From: Easton, MD Member No.: 17,042 Region Association: MidAtlantic Region 
 |
I'm in the process of trying to clean up / resto the headlights and headlight carriers on my '75 project car. Took one apart, treated the rust, and hit it with the gray paint. I order the rebuild kit from 914 Rubber. In looking at the driver's and passenger's side assemblies there's a difference I can't figure out, specifically with how the actuator arm is retained on the pin.
On the LEFT in the pic below, I've pointed to the assembly pin that has a hole in it (dark pic, sorry). A washer slides on the pin and a cotter pin goes through that hole to hold the washer and arm in place. The assembly on the RIGHT has no hole in the pin for a cotter to go through. So how is it held on? I took these apart so long ago I can't remember what was on there or why these were different. Also, is it supposed to be one spring holding the carrier on the assembly or two? TIA  |
   |
 
|
  |
Replies(1 - 4)
| 914e |
May 13 2020, 03:56 PM
Post
#2
|
|
Member Group: Members Posts: 497 Joined: 21-February 20 From: Arizona Member No.: 23,951 Region Association: Southwest Region
|
My later model ones do not have a cotter pin, I don't know if the early models did.
The slot in the body the arm goes though keeps it in place. You have to flex the arm to get it on the peg. |
 |
|
| BeatNavy |
May 13 2020, 04:01 PM
Post
#3
|
|
Certified Professional Scapegoat Group: Members Posts: 2,951 Joined: 26-February 14 From: Easton, MD Member No.: 17,042 Region Association: MidAtlantic Region
|
QUOTE(914e @ May 13 2020, 05:56 PM)  My later model ones do not have a cotter pin, I don't know if the early models did. The slot in the body the arm goes though keeps it in place. You have to flex the arm to get it on the peg. Ok, this may make sense. I may have one early / one late assembly. The one without the hole for the cotter pin had a metal actuator arm and the other one had a plastic arm. |
|
|
|
| bdstone914 |
May 13 2020, 05:28 PM
Post
#4
|
|
bdstone914 Group: Members Posts: 4,906 Joined: 8-November 03 From: Riverside CA Member No.: 1,319 |
I have never seen a hole for a cotter pin on any cars. The other end of the arm is held on with an E clip. The end on the headlight housing cant go anywhere and needs no retension.
|
|
|
|
| BeatNavy |
May 14 2020, 05:24 AM
Post
#5
|
|
Certified Professional Scapegoat Group: Members Posts: 2,951 Joined: 26-February 14 From: Easton, MD Member No.: 17,042 Region Association: MidAtlantic Region
|
QUOTE(bdstone914 @ May 13 2020, 07:28 PM) I have never seen a hole for a cotter pin on any cars. The other end of the arm is held on with an E clip. The end on the headlight housing cant go anywhere and needs no retension. That's interesting. So I wonder how that hole ended up on the one on the left (IMG:style_emoticons/default/confused24.gif) Good to know though. No retaining device needed. |
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 03:02 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.