 Washers Under Input at M/C |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Literati914 |
 Aug 27 2024, 01:52 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,934 Joined: 16-November 06 From: Dallas, TX Member No.: 7,222 Region Association: Southwest Region  |
Who carries the washer's that fit under the top seals/grommets of the Master Cylinder? I've contacted a couple places with no luck. Also, have a message out to 914rubber - if that was gonna be a suggestion. But you can find the seals/grommets all day long but not so with the required washers, apparently.
Alternatively, I'd order off just the size IF there's nothing special about them. Does anyone know this and/or the dimensions? #18 in the diagram 901 355 936 00 Attached image(s) 
|
   |
 
|
  |
Replies(1 - 4)
| bdstone914 |
Aug 27 2024, 02:07 PM
Post
#2
|
|
bdstone914 Group: Members Posts: 4,906 Joined: 8-November 03 From: Riverside CA Member No.: 1,319 |
QUOTE(Literati914 @ Aug 27 2024, 12:52 PM)  Who carries the washer's that fit under the top seals/grommets of the Master Cylinder? I've contacted a couple places with no luck. Also, have a message out to 914rubber - if that was gonna be a suggestion. But you can find the seals/grommets all day long but not so with the required washers, apparently. Alternatively, I'd order off just the size IF there's nothing special about them. Does anyone know this and/or the dimensions? #18 in the diagram 901 355 936 00 Did you call Porsche with that number? |
|
|
|
| mepstein |
Aug 27 2024, 02:13 PM
Post
#3
|
|
914-6 GT in waiting Group: Members Posts: 19,876 Joined: 19-September 09 From: Landenberg, PA/Wilmington, DE Member No.: 10,825 Region Association: MidAtlantic Region 
|
I have a Porsche dealer where I can swing by and pick up parts. They get those washers for me without a shipping charge.
Attached thumbnail(s) 
|
 |
|
| dr914@autoatlanta.com |
Aug 27 2024, 02:23 PM
Post
#4
|
|
914 Guru Group: Members Posts: 8,161 Joined: 3-January 07 From: atlanta georgia Member No.: 7,418 Region Association: None |
we sell many many of these stainless washers as they are critical to the seating of the feed lines from the reservoir so that the lines will not leak
QUOTE(Literati914 @ Aug 27 2024, 12:52 PM) Who carries the washer's that fit under the top seals/grommets of the Master Cylinder? I've contacted a couple places with no luck. Also, have a message out to 914rubber - if that was gonna be a suggestion. But you can find the seals/grommets all day long but not so with the required washers, apparently. Alternatively, I'd order off just the size IF there's nothing special about them. Does anyone know this and/or the dimensions? #18 in the diagram 901 355 936 00 |
|
|
|
| Literati914 |
Aug 27 2024, 02:39 PM
Post
#5
|
|
Senior Member Group: Members Posts: 1,934 Joined: 16-November 06 From: Dallas, TX Member No.: 7,222 Region Association: Southwest Region |
QUOTE(dr914@autoatlanta.com @ Aug 27 2024, 03:23 PM) we sell many many of these stainless washers as they are critical to the seating of the feed lines from the reservoir so that the lines will not leak QUOTE(Literati914 @ Aug 27 2024, 12:52 PM) Who carries the washer's that fit under the top seals/grommets of the Master Cylinder? I've contacted a couple places with no luck. Also, have a message out to 914rubber - if that was gonna be a suggestion. But you can find the seals/grommets all day long but not so with the required washers, apparently. Alternatively, I'd order off just the size IF there's nothing special about them. Does anyone know this and/or the dimensions? #18 in the diagram 901 355 936 00 @mepstein I appreciate the info - I'm gonna place an order with George though 'cause I need a few other bits and pieces. George @dr914@autoatlanta.com - Thanks for the heads-up, 'cause I have problems finding stuff on your site sometimes tbh. |
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 07:11 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.