Need measurement between trailing arms..., to determine correct axle length w/Boxster trans |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
Need measurement between trailing arms..., to determine correct axle length w/Boxster trans |
neo914-6 |
Dec 2 2007, 09:33 AM
Post
#1
|
neo life Group: Members Posts: 5,086 Joined: 16-January 03 From: Willow Glen (San Jose) Member No.: 159 |
I'm not sure if this would be a consistent measurement from car to car. My arms have been rebuilt and I can't get them to an alignment shop. I need to make sure my axles have the correct lengths. Because of the Boxster design, they are unequal.
1. I need measurement between the inner faces of the arms. 2. What is the longitudinal tolerance of Constant Velocity joints? This will determine if I need to have the axle(s) modified. |
McMark |
Dec 2 2007, 11:16 AM
Post
#2
|
914 Freak! Group: Retired Admin Posts: 20,179 Joined: 13-March 03 From: Grand Rapids, MI Member No.: 419 Region Association: None |
Felix, I'll try to measure something this afternoon, but the measurement will be affected by your rear toe settings.
|
neo914-6 |
Dec 2 2007, 12:48 PM
Post
#3
|
neo life Group: Members Posts: 5,086 Joined: 16-January 03 From: Willow Glen (San Jose) Member No.: 159 |
Felix, I'll try to measure something this afternoon, but the measurement will be affected by your rear toe settings. Yes, that's what I'm concerned about. I "should" have take measurements before removing them but even then the large mounting bolt holes can affect that measurement. I wonder how much toe adjustment is made at this mount and/or the tolerance on the CV's, if any... (IMG:style_emoticons/default/idea.gif) Thanks! |
okieflyr |
Dec 2 2007, 01:04 PM
Post
#4
|
9fauxteen Group: Members Posts: 816 Joined: 9-January 05 From: Phila PA Member No.: 3,426 Region Association: North East States |
Felix, I'm in the process of the same type of install.
Mine is a 1.8t, that I'm upgrading from the 901 to a Passat trans. I found a 1000 mile trans on e-bay, and bought it for $285.00 ! I'm getting the trans back any day now from getting the Quaiffe installed. I'm interested in your axle development as my need will be similar to yours. I could measure my trailing arms/hubs, but they are at full droop and may not be acurate enough. (IMG:style_emoticons/default/popcorn[1].gif) Kevin |
Wes V |
Dec 2 2007, 01:19 PM
Post
#5
|
Member Group: Members Posts: 482 Joined: 11-October 07 From: Los angeles Member No.: 8,211 |
I'm really looking forward to see how this works out for you two guys!!
Did you guys center the engine (side to side), which would offset the transmission CV joint flanges, or offset the engine and trans, so that the CV joint flanges are centered. Okieflyr; are the CV flanges on the Audi transmission the same as what Neo914V6 has on his Boxster transmission? Wes |
johnlush |
Dec 2 2007, 02:52 PM
Post
#6
|
What's all this then? Group: Members Posts: 372 Joined: 26-May 04 From: Cheyenne, WY Member No.: 2,108 Region Association: Rocky Mountains |
Hi Felix,
I just measured my car and came up with 38.5 inches. That's measuring just forward of the large hole in the trailing arms that the stub axles pass through. Hope this helps. John |
toon1 |
Dec 2 2007, 04:03 PM
Post
#7
|
Senior Member Group: Members Posts: 1,849 Joined: 29-October 05 From: tracy,ca Member No.: 5,022 |
I came up with 38 11/16". front edge of the the large hole.
That large hole has a lip that sticks inward twards the center of the car. I made the measurement from edge to edge of the lip. Keith |
Lo-Fi Version | Time is now: 31st October 2024 - 04:52 PM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |