Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

> How To Replace Alternator, 1.8l FI
knuckledrgr914
post Apr 10 2009, 02:05 PM
Post #1


Newbie
*

Group: Members
Posts: 46
Joined: 17-June 08
From: Meridian
Member No.: 9,180
Region Association: None



Do I need to drop the motor/trani to replace my alternator? If not, advice?!? (IMG:style_emoticons/default/confused24.gif)

Thanks,
Brad
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
 
Reply to this topicStart new topic
Replies(1 - 12)
dr914@autoatlanta.com
post Apr 10 2009, 02:30 PM
Post #2


914 Guru
*****

Group: Members
Posts: 8,092
Joined: 3-January 07
From: atlanta georgia
Member No.: 7,418
Region Association: None



no way get it from underneath. If you have a 75 76 you will have to remove the heat exchanger. If 70-74 just the left heater plumbing
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
VaccaRabite
post Apr 10 2009, 02:37 PM
Post #3


En Garde!
**********

Group: Admin
Posts: 13,584
Joined: 15-December 03
From: Dallastown, PA
Member No.: 1,435
Region Association: MidAtlantic Region



Nope.


Rasie the rear of the car as hgh as you can get it.
remove the drivers side wheel.

from under the car, remove the dust boot that goes to the fan to the alt.
Follow the wires from the Alt to the relay board in the engine compartment. Pull the top off the board and remove the alternator wires from the relay board, and the wire that goes to the starter.

go back under the car. You will see a bit of engine tin that goes along the shelf. it is divided in two sections. A long section and a short one. Remove the short section of tin. there is a hidden bolt on the seam near the engine shelf, feel for it.

Now release belt tension on the alt. You may need to get a star point nut driver for this. If so, go to true value or HD and replace these bolts with regular metric allen bolts.

remove the alternator belt. Plan on replacing it.

Alternator is held in with 2 m8 allen (or soon to be replaced star point) bolts. Take them off. One of them is already loose, since it is what you loosened when you released tension on the alternator belt. You are still under the car, try not to let the sucker fall on your face. Its heavy.

Now, find whatever I have forgotten about, and unhook that. Wiggle the old alt around till it out of the car. Again, you are doing this from under the car, don't let it fall on your head.

Thats it. Buy a new one and replace everything. Easy.

Zach
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
SirAndy
post Apr 10 2009, 02:49 PM
Post #4


Resident German
*************************

Group: Admin
Posts: 41,854
Joined: 21-January 03
From: Oakland, Kalifornia
Member No.: 179
Region Association: Northern California



I've done it both ways and i have to say, dropping the engine is quicker.

There's just not enough room up there to work, even with the car on a lift. It takes twice as long as dropping the engine.
(IMG:style_emoticons/default/popcorn[1].gif) Andy
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
turboturtle
post Apr 10 2009, 02:51 PM
Post #5


Member
**

Group: Members
Posts: 56
Joined: 19-February 09
From: Little Rock, Arkansas
Member No.: 10,068
Region Association: None



I've got to do this as well. Anything wrong with having my unit rebuilt, or should just I replace it and forget about it.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
McMark
post Apr 10 2009, 03:05 PM
Post #6


914 Freak!
***************

Group: Retired Admin
Posts: 20,179
Joined: 13-March 03
From: Grand Rapids, MI
Member No.: 419
Region Association: None



I can swap on an early car in about 1 hour. There's a write up here.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
ClayPerrine
post Apr 10 2009, 04:35 PM
Post #7


Life's been good to me so far.....
***************

Group: Admin
Posts: 15,879
Joined: 11-September 03
From: Hurst, TX.
Member No.: 1,143
Region Association: NineFourteenerVille



QUOTE(McMark @ Apr 10 2009, 04:05 PM) *

I can swap on an early car in about 1 hour. There's a write up here.

(IMG:style_emoticons/default/agree.gif)

Just did it twice last weekend. Easy to do.


User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Cap'n Krusty
post Apr 10 2009, 05:41 PM
Post #8


Cap'n Krusty
**********

Group: Members
Posts: 10,794
Joined: 24-June 04
From: Santa Maria, CA
Member No.: 2,246
Region Association: Central California



QUOTE(SirAndy @ Apr 10 2009, 01:49 PM) *

I've done it both ways and i have to say, dropping the engine is quicker.

There's just not enough room up there to work, even with the car on a lift. It takes twice as long as dropping the engine.
(IMG:style_emoticons/default/popcorn[1].gif) Andy


Geeeezzzzz, Andy. It takes 3-4 hours for most people to R&R an FI engine, and .75-1hr to replace the alternator in the car. For the original poster, BE SURE you check the length of the B+ stud! Adjust as necessary to clear the rear cover of the alternator. The Cap'n
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
SirAndy
post Apr 10 2009, 06:05 PM
Post #9


Resident German
*************************

Group: Admin
Posts: 41,854
Joined: 21-January 03
From: Oakland, Kalifornia
Member No.: 179
Region Association: Northern California



QUOTE(Cap'n Krusty @ Apr 10 2009, 04:41 PM) *

Geeeezzzzz, Andy. It takes 3-4 hours for most people to R&R an FI engine, and .75-1hr to replace the alternator in the car.

I guess that makes me one heck of a quick engine dropper!
(IMG:style_emoticons/default/biggrin.gif) Andy
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
dflesburg
post Apr 10 2009, 07:15 PM
Post #10


Senior Member
***

Group: Members
Posts: 1,722
Joined: 6-April 04
From: Warm and Cheerful Centerville Ohio
Member No.: 1,896
Region Association: None



anytime you buy a new alternator get the higher amp one made for the 912e.

Or

don't but I do.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
turboturtle
post Apr 11 2009, 04:41 PM
Post #11


Member
**

Group: Members
Posts: 56
Joined: 19-February 09
From: Little Rock, Arkansas
Member No.: 10,068
Region Association: None



QUOTE(dflesburg @ Apr 10 2009, 05:15 PM) *

anytime you buy a new alternator get the higher amp one made for the 912e.

Or

don't but I do.


Higher amperage would be nice. Maybe my guy could modify mine for a few more amps. I'll be pulling mine out this week sometime.

Thanks for the reference

Bob
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
euro911
post Apr 11 2009, 05:48 PM
Post #12


Retired & living the dream. God help me if I wake up!
*****

Group: Members
Posts: 8,857
Joined: 2-December 06
From: So.Cal. & No.AZ (USA)
Member No.: 7,300
Region Association: Southern California



Yes, your electrical rebuild shop should be able to make a higher amperage unit for you (which is a good idea) (IMG:style_emoticons/default/idea.gif)

I found it goes a lot quicker if you have another person (who knows what the job entails) doing the top-side stuff while you're under the car doing the bottom stuff (or vice-versa) (IMG:style_emoticons/default/unsure.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
knuckledrgr914
post Apr 11 2009, 08:44 PM
Post #13


Newbie
*

Group: Members
Posts: 46
Joined: 17-June 08
From: Meridian
Member No.: 9,180
Region Association: None



QUOTE(euro911 @ Apr 11 2009, 05:48 PM) *

I found it goes a lot quicker if you have another person (who knows what the job entails) doing the top-side stuff while you're under the car doing the bottom stuff (or vice-versa) (IMG:style_emoticons/default/unsure.gif)

Thanks for the offer to help euro911! I'll pick you up from the airport when you fly into Boise, Idaho! What time do you arrive? (IMG:style_emoticons/default/piratenanner.gif) (IMG:style_emoticons/default/happy11.gif) (IMG:style_emoticons/default/lol-2.gif)

Actually, thanks to all that provided insight into replacing my alternator. I hope to get some time to work on it in a couple days.

Brad
User is offlineProfile CardPM
Go to the top of the page
+Quote Post

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



- Lo-Fi Version Time is now: 31st October 2024 - 05:33 PM