 Converting from single to dual webers, how do I go about modifying the fuel pump? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| pete914 |
 Feb 22 2008, 05:52 AM
Post
#1
|
|
Member  Group: Members Posts: 178 Joined: 21-August 07 From: east coast Member No.: 8,025  |
Did a quick search and the only thing that came up was the electrical wiring article which has already been done on the car. Anyway, putting a set of weber idf 40's on my 1.8L. Right now I have a holley single carb on the engine. Do i run two lines ouf the fuel pump?
Anyone know of a good place to read up on this? Thanks much Oh, here's a picture of the carbs. You guys might have seen these in the F/S section. They ended up on eBay. What other parts am I going to need besides the bolts for the manifolds? I will need something for the throttle cable to attached somewhere rigid correct? Does the linkage need anything additional? I've actually never seen one of these on a 'teener in person, so I'm a little confused. (IMG:http://i35.photobucket.com/albums/d189/pba110/914/101_1608.jpg) (IMG:http://i35.photobucket.com/albums/d189/pba110/914/101_1609.jpg) (IMG:http://i35.photobucket.com/albums/d189/pba110/914/101_1610.jpg) |
   |
 
|
  |
Replies
| rhodyguy |
Feb 22 2008, 08:59 AM
Post
#2
|
|
Chimp Sanctuary NW. Check it out. Group: Members Posts: 22,240 Joined: 2-March 03 From: Orion's Bell. The BELL! Member No.: 378 Region Association: Galt's Gulch |
in direction of flow. tank, filter, pump (single outlet, like the cb unit mentioned), single line to the engine bay, T in bay with the lines branching to the carbs. you'll need to fab up a STOUT bracket to secure the throttle cable.
k |
|
|
|
| pete914 |
Feb 22 2008, 03:39 PM
Post
#3
|
|
Member Group: Members Posts: 178 Joined: 21-August 07 From: east coast Member No.: 8,025 |
Awesome. thanks Everyone. There is a pressure regulator after the pump. However, it doesn't have a psi value. Just 1, 2, 3 or something like that. Perhaps that corresponds to psi though.
I'll take a better look when the weather improves. 38 and raining right now. Lovely. Can't wait for spring! yo, type47, how did the installation go? I actually ordered an almost complete d-jet setup (seller thought it was L-jet) thinking I was going to restore the FI. Ended up backing off the project though. I think the dual webers are the answer for now... |
|
|
|
Posts in this topic
pete914 Converting from single to dual webers Feb 22 2008, 05:52 AM
Spoke If you're already running carbs and your fuel ... Feb 22 2008, 06:24 AM type47 i'm probably not the one who should answer as ... Feb 22 2008, 06:25 AM SGB i had a pressure regulator but took it out. it is... Feb 22 2008, 06:54 AM purple I had one fuel like coming from the pump. the othe... Feb 22 2008, 07:31 AM
type47
yo, type47, how did the installation go?
easy... Feb 23 2008, 01:48 PM rhodyguy if you're going to use an unregulated fuel pum... Feb 23 2008, 10:30 AM brer I responded to these when they were first posted.
... Feb 23 2008, 01:31 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 08:55 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.