 Best inexpensive header, suggestions? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Brando |
 Feb 29 2008, 05:26 PM
Post
#1
|
|
BUY MY SPARE KIDNEY!!!  Group: Members Posts: 3,935 Joined: 29-August 04 From: Santa Ana, CA Member No.: 2,648 Region Association: Southern California  |
I can't plop down the $1k+ for a tangerine, so I need some direction on an inexpensive, durable (read: wont rust like madness), clean (read: won't leak so I can fab up heat). I'm not sure what a decent one will cost... Definitely looking for a boost over SSI's in performance.
My guesses are... Euro-Race Kerry Hunter ??? thanks for your input. |
   |
 
|
  |
Replies
| Brando |
Feb 29 2008, 10:01 PM
Post
#2
|
|
BUY MY SPARE KIDNEY!!! Group: Members Posts: 3,935 Joined: 29-August 04 From: Santa Ana, CA Member No.: 2,648 Region Association: Southern California |
Sweet. If I ever go six, I can use an MSDS header (they don't have a 4-cyl header listed on their site).
So, 4 cylinder options? |
|
|
|
| Maltese Falcon |
Mar 1 2008, 04:57 PM
Post
#3
|
|
914 Guru Group: Members Posts: 5,209 Joined: 14-September 04 From: Mulholland SoCal Member No.: 2,755 Region Association: None  |
QUOTE(Brando @ Feb 29 2008, 08:01 PM)  Sweet. If I ever go six, I can use an MSDS header (they don't have a 4-cyl header listed on their site). So, 4 cylinder options? Brando, the T-4 race header that we build is ONLY avilable thru Auto Atlanta (contract build). Check their site in the 914 engine/ exhaust area and it will come up. Good HP/TQ for the price ! Marty msds |
|
|
|
| lotus_65 |
Mar 4 2008, 05:30 AM
Post
#4
|
|
Senior Member Group: Members Posts: 1,609 Joined: 21-March 05 From: minneapolis, mn Member No.: 3,795 Region Association: Northstar Region |
QUOTE(Maltese Falcon @ Mar 1 2008, 04:57 PM) QUOTE(Brando @ Feb 29 2008, 08:01 PM) Sweet. If I ever go six, I can use an MSDS header (they don't have a 4-cyl header listed on their site). So, 4 cylinder options? Brando, the T-4 race header that we build is ONLY avilable thru Auto Atlanta (contract build). Check their site in the 914 engine/ exhaust area and it will come up. Good HP/TQ for the price ! Marty msds ...looked twice, didn't see 'em. |
|
|
|
Posts in this topic
Brando Best inexpensive header Feb 29 2008, 05:26 PM
dr914@autoatlanta.com
I can't plop down the $1k+ for a tangeri... Feb 29 2008, 05:34 PM
Vacca Rabite
Brando, the T-4 race header that we build is ONL... Mar 4 2008, 07:48 AM lotus_65
[quote name='lotus_65' post='1004689' date='Mar 4... Mar 4 2008, 08:02 PM Phoenix 914-6GT http://www.triadwestperformance.com/ Mar 1 2008, 11:20 AM Brando Thanks Marty, I greatly appreciate your reply. I s... Mar 2 2008, 09:26 PM Maltese Falcon [quote name='Brando' post='1004233' date='Mar 2 20... Mar 3 2008, 08:59 PM purple I have a eurorace header and it sounds very nice. ... Mar 3 2008, 07:47 AM Vacca Rabite
I have a eurorace header and it sounds very nice.... Mar 3 2008, 09:57 AM purple
I have a eurorace header and it sounds very nice... Mar 3 2008, 12:09 PM jasons
Did you put header wrap on the header, or a ther... Mar 3 2008, 05:34 PM Racer Chris One way to help the cable clear the header: Mar 3 2008, 05:08 PM purple
One way to help the cable clear the header:
Int... Mar 3 2008, 08:28 PM Racer Chris
One way to help the cable clear the header:
In... Mar 4 2008, 08:43 AM purple
[quote name='purple' post='1004596' date='Mar 3 2... Mar 4 2008, 09:19 AM purple hold on...13ga sheet metal? as in .0897 inches thi... Mar 4 2008, 05:26 PM jd74914
hold on...13ga sheet metal? as in .0897 inches th... Mar 4 2008, 08:19 PM Vacca Rabite as sheet metal goes, 13 gauge is kinda thick. You... Mar 4 2008, 05:28 PM purple whelp, I found some 12ga :evilgrin: galvanized st... Mar 4 2008, 10:48 PM Vacca Rabite
whelp, I found some 12ga :evilgrin: galvanized s... Mar 5 2008, 01:08 PM Racer Chris The ones I supply with my headers have the bolt ho... Mar 5 2008, 02:51 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 2nd April 2026 - 04:28 PM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.