 This may be a stupid question but here it goes |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Badass43 |
 Jul 18 2008, 11:01 AM
Post
#1
|
|
Newbie  Group: Members Posts: 26 Joined: 11-June 08 From: Louisiana Member No.: 9,163 Region Association: None  |
Hey Guys,
what are the I.D. measurments of stock cylinders? I am getting ready to rebuild my 2.0 and the cylinders that are on it measure right under 96mm I.D.. Is this stock cylinders? The pistons in the engine are dished so I'm almost sure they are stock, but there are no markings on top like type 1 pistons. My thinking is that for 94mm stock pistons the cylinder would be a little larger right? I want to go to 96mm P/C for addred performance. What does it cost to have the stock cylinders bored for 96mm pistons? and who does this? Randy |
   |
 
|
  |
Replies
| Katmanken |
Jul 19 2008, 07:12 PM
Post
#2
|
|
You haven't seen me if anybody asks... Group: Members Posts: 4,738 Joined: 14-June 03 From: USA Member No.: 819 Region Association: Upper MidWest |
Hows about a picture of the pistons.....
That might help us zero in on what piston/cylinder set you have. Probably not 96mm NPR's... my spare set have flat tops.. Ken |
|
|
|
Posts in this topic
Badass43 This may be a stupid question but here it goes Jul 18 2008, 11:01 AM
Vacca Rabite Stock is 94mm on a 2.0.
if you have 96mm cylinder... Jul 18 2008, 11:10 AM SLITS Stock on a 2.0 is 94mm ... pistons will measure ab... Jul 18 2008, 11:10 AM Badass43 The guy I bought the engine from did say that the ... Jul 18 2008, 11:35 AM
Todd Enlund
Did they make dished 96mm pistons?
I've se... Jul 18 2008, 02:28 PM orange914
Did they make dished 96mm pistons?
I've s... Jul 19 2008, 02:06 PM Vacca Rabite Sounds like you have a 2056 then. You are ahead o... Jul 18 2008, 11:42 AM Badass43 I Have calipers and I pulled the cylinder out far ... Jul 18 2008, 03:37 PM Vacca Rabite
Does someone sell like copper head gaskets to use... Jul 19 2008, 02:18 PM cooltimes How about posting a photo of the 914. Maybe someon... Jul 19 2008, 03:26 PM Badass43 Well I bought this engine from the classifieds her... Jul 19 2008, 04:53 PM Badass43 Oop, lets try that again. Jul 19 2008, 04:57 PM Badass43 I won't be able to get pictures of the pistons... Jul 19 2008, 08:19 PM Badass43 Ok,
Here is a picture of one of the pistons.
Ra... Jul 21 2008, 09:42 PM Badass43 Who sells a good set of piston rings to fit these ... Jul 22 2008, 09:43 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 12th June 2024 - 12:35 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.