 Billitt hubs, 4bolt hubs that take 911sc vented disk |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| ventedrib |
 Aug 11 2008, 05:16 PM
Post
#1
|
|
Member  Group: Members Posts: 104 Joined: 10-August 08 From: Monroe La. Member No.: 9,406 Region Association: South East States  |
Hy I'm a newby to this site but not a newby teener. I saw some billitt hubs on here i think that were 4bolt hubs that would exept 911 vented disk. Has anybody tried these with the bmw 320 calipers it should work I know a mid 80's bmw had vented rotors right.
|
   |
 
|
  |
Replies
| TravisNeff |
Aug 26 2008, 09:31 PM
Post
#2
|
|
914 Guru Group: Members Posts: 5,082 Joined: 20-March 03 From: Mesa, AZ Member No.: 447 Region Association: Southwest Region 
|
I asked the question for my edification, not as an attack.you seem very knowlegable on this topic so it was a "no brainer" to ask. I agree on the potential price point.however, after buying used struts and brakes you may have to overhaul them that raises the price quite a bit. I have also recently seen someone selling a new complete 5 bolt billet conversion at a great price. So my question is going that route asking for trouble (billet).
|
|
|
|
Posts in this topic
ventedrib Billitt hubs Aug 11 2008, 05:16 PM
Mikey914
Hy I'm a newby to this site but not a newby t... Aug 11 2008, 11:13 PM McMark Moved to the garage... Aug 23 2008, 11:56 PM Phoenix 914-6GT
Hy I'm a newby to this site but not a newby t... Aug 24 2008, 12:31 AM Eric_Shea If you want to retain the 4-lug and have a vented ... Aug 24 2008, 01:34 AM
Travis Neff
If you want to go 5-lug a 911 front end is a bett... Aug 25 2008, 12:50 PM Phoenix 914-6GT I belive Rich will sell this setup for a good pric... Aug 24 2008, 02:01 AM Travis Neff :bump: Aug 26 2008, 10:55 AM Bleyseng I think its more like the weanie bearings on a sto... Aug 26 2008, 05:14 PM smdubovsky I have no dog in this particular fight but I'v... Aug 26 2008, 05:19 PM Travis Neff I understand there are bigger bearings that will l... Aug 26 2008, 05:42 PM Eric_Shea
Just saw this... never said that 914 spindles fa... Aug 26 2008, 08:22 PM Travis Neff And yes this was somewhat of a leading question. I... Aug 26 2008, 09:44 PM Eric_Shea
I'm not sure. I wouldn't think a hub wo... Aug 27 2008, 01:29 AM Travis Neff Thanks Eric,
That was what I was after. Aug 27 2008, 11:15 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 16th June 2024 - 07:59 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.