 2.7 CIS to Carbs - how much HP loss? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Scott S |
 Jul 2 2009, 03:15 PM
Post
#1
|
|
Small Member  Group: Members Posts: 1,698 Joined: 30-April 03 From: Colorado Member No.: 633  |
Hi All -
Got a line on a rebuilt 2.7 out of a 1977 911S. It is 100% complete including the full CIS system. What kind of power loss would I experience if I stripped off the CIS and went with carbs? The motor is only 165hp to begin with... Thanks! Scott S |
   |
 
|
  |
Replies
| carr914 |
Jul 2 2009, 04:43 PM
Post
#2
|
|
Racer from Birth Group: Members Posts: 124,882 Joined: 2-February 04 From: Tampa,FL Member No.: 1,623 Region Association: South East States  |
I would think that you would H.P. & Torque with the switch. 2.7s are fairly low compression motors (remember when they were built - Fuel availability & emissions) and the CIS is made to work with this compression. Without a Cam change to work with the carbs it will suffer. However you can make a 2.7 into a great motor. I expect my 2.7 to put out 225-240HP
T.C. |
 |
|
Posts in this topic
Scott Schroeder 2.7 CIS to Carbs - how much HP loss? Jul 2 2009, 03:15 PM
brant Scott,
I heard about that motor
seemed like a re... Jul 2 2009, 03:20 PM Cupomeat I cannot support the following with empirical evid... Jul 2 2009, 03:21 PM turboman808 From what I have seen on graphs you get peaks and ... Jul 2 2009, 03:46 PM 9146986 Why not just keep the CIS? Jul 2 2009, 10:11 PM pcar916 When I bought my car it had a 2.7L motor built up ... Jul 2 2009, 11:13 PM GeorgeRud If you don't have it, I would get Bruce Anders... Jul 2 2009, 11:29 PM ahdoman If the CIS is intact and working stick with it. Yo... Jul 3 2009, 12:10 AM carr914
When I bought my car it had a 2.7L motor built up... Jul 3 2009, 06:15 AM
pcar916
[quote name='pcar916' post='1188039' date='Jul 3 ... Jul 3 2009, 07:45 AM Project 6 Wayne at Pelican claims to have installed a CIS mo... Jul 3 2009, 07:50 AM J P Stein I know a few folks that run Webers on an otherwise... Jul 3 2009, 08:51 AM Gint I'd probably just use the CIS. But if you buy... Jul 3 2009, 08:53 AM scotty
I know a few folks that run Webers on an otherwis... Jul 3 2009, 10:28 AM naro914 I have a 2.7 in Huey at the moment, with Webers. I... Jul 4 2009, 10:56 AM Mountain914 Just want to throw this out there - since the titl... Jul 4 2009, 11:44 AM J P Stein
Just want to throw this out there - since the tit... Jul 4 2009, 01:38 PM ArtechnikA
A good illustration of the possibilities of the 2... Jul 4 2009, 02:02 PM J P Stein
A good illustration of the possibilities of the ... Jul 4 2009, 04:02 PM ArtechnikA
Yeah,yeah, some folks go all gaga over the MFI se... Jul 4 2009, 05:31 PM naro914 This is a good discussion....
I have carbs. I lik... Jul 4 2009, 04:14 PM J P Stein
This is a good discussion....
I have carbs. I li... Jul 4 2009, 07:12 PM 9146986 As long as the carbs are optimized for the engine,... Jul 5 2009, 11:18 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 10th May 2025 - 05:13 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.